No abstract

In the aquatic environment, heavy metals such as lead ions Pb (II) are of particular importance. These are due to Pb (II) being toxic at concentrations over 0.01 mg/L, when taken continuously over an extended length of time. Organs including the heart, gut, and kidneys are seriously harmed by Pb (II) intoxication. The neurological, reproductive, and bone systems are also affected. The removal of Pb (II) from aquatic environments is, therefore, crucial. Low density Polyethylene (LDPE) is grafted by radiation with Acrylonitrile and acrylic acid (PE-g-AN/AAc) for the adsorption of Pb (II). Factors that control the grafting process for optimum conditions, such as the effect of solvents, the air atmosphere, inhibitors, comonomer concentration, and composition and irradiation dose, are studied to obtain a high grafting yield without homopolymer formation and a higher water uptake. The results showed that the addition of 2.5% by wt% ferric chloride salt effectively inhibits homoploymerization of a mixture of 30% methanol and 70% H2O used as a solvent in nitrogen. The highest graft yield obtained was 320% at a 25 kGy radiation dose with an 80/20 monomer composition and 60% comonomer concentration. The resulting composite films were characterized by XRD to analyze the dispersion properties of the material, SEM for the surface morphology, FTIR analysis for the functional groups, TGA, DSC for the thermal stability and elongation, and tensile strength for the mechanical properties. The uptake of Pb (II) from lead nitrate aqueous solution by (PE-g-AN/AAc) was observed under different conditions of the degree of grafting, contact time, metal ion concentration, and pH. The results obtained suggest LDPE-g-p (AN/AAc) as a superabsorbent for the Pb (II) ion’s removal from an aqueous solution.

Graft copolymerization has been a popular technique in recent years for adding different functional groups to polymers. In our research, polypropylene (PP) films are grafted with acrylonitrile (An) and acrylic acid (AAc) monomers to make them hydrophilic while retaining their mechanical qualities. Gamma radiation is used in this approach to establish active spots on an inert polymer that are appropriate for adding monomers radicals to form grafts, a procedure that is extremely difficult to perform using normal chemical processes. The graft parameters are investigated in order to acquire the highest percentage of graft. FTIR (Fourier transform infrared spectroscopy) spectra are used to analyze the grafting of AAc and An. SEM (scanning electron microscopy) and XRD (X-ray diffraction) micrographs are used to validate them. The specimens’ tensile strength and hardness are measured and contrasted with blank PP films. Measurements are made of the effects of grafting on the tensile strength and elongation of the films, and a crucial grafting degree is established in order to preserve these properties. Water uptake is measured to adapt the copolymer to water treatment, and thermal behavior TGA (thermal gravimetric analysis) and DSC (diffraction scanning calorimeter) of the produced copolymer were performed. The elimination of cadmium was verified by an atomic absorption spectrophotometer (AAS) under different conditions of pH, time, and degree of grafting.

No abstract

No abstract

Due to the high cost of transportation and the lack of established, affordable recycling routes, the rate of recycling of previously used polystyrene foam is extremely low. In this study, a novel treatment technique will be used to examine the feasibility of using waste polystyrene foam as a raw material to produce wood plastic composite (WPC). Where, the recycled polystyrene (rPS) foam waste was first dissolved in methylene chloride and compounded directly with flax fiber (FF) and additives forming a composite paste. The composite paste was then passes through vacuum distillation process for drying the composite paste and also for solvent recovery to reuse it in a further process. The dried composite was processed through thermal mixer extruding and compression molding processes to form the final WPC. The study discovered that WPC with 60 parts per hundred parts of resins (phr) of FF and 2 phr of dioctylphthalate (DOP) may be used to create rPS/FF composite with a proper tensile strength of 19.3 MPa, flexural strength of 78 MPa and compressive strength of 173 MPa compared to another WPS,s based on PVC, HDPE and PP . In addition of that the resulted composite possesses a great potential in manufacturing WPC with environmental and economical demanding application as wooden furniture and as a wooden panels for cladding the exterior building faces.