This study scrutinizes the reliability and validity of existing analyses that focus on the impact of various environmental factors on a photovoltaic (PV) system’s performance. For the first time, four environmental factors (the accumulation of dust, water droplets, birds’ droppings, and partial shading conditions) affecting system performance are investigated, simultaneously, in one study. The results obtained from this investigation demonstrate that the accumulation of dust, shading, and bird fouling has a significant effect on PV current and voltage, and consequently, the harvested PV energy. ‘Shading’ had the strongest influence on the efficiency of the PV modules. It was found that increasing the area of shading on a PV module surface by a quarter, half, and three quarters resulted in a power reduction of 33.7%, 45.1%, and 92.6%, respectively. However, results pertaining to the impact of water droplets on the PV panel had an inverse effect, decreasing the temperature of the PV panel, which led to an increase in the potential difference and improved the power output by at least 5.6%. Moreover, dust accumulation reduced the power output by 8.80% and the efficiency by 11.86%, while birds fouling the PV module surface was found to reduce the PV system performance by about 7.4%.

Summary Integration of solar concentrators with photovoltaic (PV) systems reduces the required number of PV panels, which often account for the major costs of PV systems. The linear Fresnel reflector mirror is considered more effective because of its simplicity and effortless fabrication. An experimental test rig of a concentrated PV/thermal system that employs a linear configuration and horizontal absorber was built for evaluating its electrical and thermal performances. The considered concentrator consists of various widths of flat glass mirrors, which positioned with different angles, and with sun light focusing on the PV cells that fixed over an active cooling system. The experimental investigation of the proposed concentrated PV/thermal system shows that higher electrical and thermal efficiencies can be achieved at comparatively high temperature levels than that typically utilized in a nonconcentrated PV/thermal system. The characteristics of PV cells also indicate that the electrical efficiency values in case of no concentration and with concentration ratio of 6.0 are 9.6%, and 11%, respectively. The measured values for the inlet and outlet cooling water temperatures of the receiver showed that the maximum outlet temperature reached was 75°C with a flow rate of 0.025 L/min, and the product thermal efficiency was 62.3%. These obtained results illustrate an adequate and good thermal and electrical performance under the meteorological weather conditions of the province of Al‐Karak in Jordan.

No abstract

The use of a concentrated photovoltaic (CPV) system significantly reduces the required solar cell area that often accounts for the major cost of a PV solar system. A comprehensive performance analysis of a multi-mirror solar concentrated hybrid PV thermal (CPVT) system was conducted. Among different concentrating systems, Linear Fresnel Reflector (LFR) systems are more effective due to their simplicity of operation and low fabrication cost. A mathematical model and the simulation of a CPVT system employing a linear configuration and horizontal absorber is developed here in order to evaluate its performance parameters, using a FORTRAN programing technique. The concentrator system consists of, different width of flat glass mirrors placed under various inclination angles, focusing sunlight on to the PV solar cells mounted along the active cooling system. The effect of focus distance on concentration ratio, collector width, and heat gained by the coolant fluid are investigated. All parameters of the linear Fresnel reflector solar concentrator system are determined and the effect of cooling mass flow rate and cooling inlet temperature upon the system performance is evaluated. With regards to simulation results obtained via the focus distances, the width of mirrors decreased by increasing the number of mirrors, and in turn by increasing the focus distances, this resulted in an increase in CR values. For the specific number of mirrors, concentration ratio increased simultaneously increasing the focus distance; furthermore, increasing the number of mirrors resulted in a reduction in both the width of the mirrors and their inclination angles, and an increase in CR values. The results further confirmed that the total (combined electrical-thermal) efficiency is higher than that of the individual electrical as well as thermal efficiency; reaching approximately 80% and showed no sensitivity to the rises in cooling water temperature for temperature cases under consideration.

No abstract

The ever-increasing popularity of finding alternative forms of renewable energy has seen an increased interest and utilization of wind energy. The objective of this research therefore, is to evaluate the environmental impacts and energy performance of wind farms. This study was operationalized in Jordan using a life-cycle assessment (LCA) method. The environmental impact is evaluated through lifecycle emissions that include all emissions during various phases of the project. The energy performance is illustrated by the energy indicators. The latter is the energy payback ratio (EPR) and the energy payback time (EPT). This study was conducted on a 38 Vestas V112 3-MW wind turbine located in the southern region of Tafilah in Jordan that is host to the country’s first wind farm. SimaPro 7.1 software was used as the modeling platform. Data for this study were collated from various sources, including, manufacturers, the wind turbine farm, and local subcontractors. A software database was used for the modeling process, and the data obtained modeled in accordance with ISO 14040 standards. The findings of this study indicate that the impacts of the transportation and installation phases were moderate, with the largest negative environmental impact deriving from the manufacturing phase. To remedy some of the negative impacts in these phases, green cement was used for the turbine foundation to limit the environmental impacts to be had during the installation phase, while the transportation phase saw the utilization of locally-manufactured turbines. Furthermore, an evaluation of the study’s results revealed that the energy payback period of the wind farm is approximately 0.69 year (8 months), while the payback ratio is 29, and the annual CO2 saving estimated to be at 2.23 × 108 kg, 3.02 × 108 kg, 3.10 × 108 kg for an annual generated power of 371, 501, and 515 GWh/year.

No abstract

No abstract