Cavitation erosion and corrosion of structural materials are serious concerns for marine and offshore industries. Durability and performance of marine components are severely impaired due to degradation from erosion and corrosion. Utilization of advanced structural materials can play a vital role in limiting such degradation. High entropy alloys (HEAs) are a relatively new class of advanced structural materials with exceptional properties. In the present work, we report on the cavitation erosion behavior of AlCoCrFeNi HEA in two different media: distilled water with and without 3.5wt% NaCl. For comparison, conventionally used stainless steel SS316L was also evaluated in identical test conditions. Despite lower hardness and yield strength, the HEA showed significantly longer incubation period and lower erosion-corrosion rate (nearly 1/4th) compared to SS316L steel. Enhanced erosion resistance of HEA was attributed to its high work-hardening behavior and stable passivation film on the surface. The AlCoCrFeNi HEA showed lower corrosion current density, high pitting resistance and protection potential compared to SS316L steel. Further, HEA showed no evidence of intergranular corrosion likely due to the absence of secondary precipitates. Although, the degradation mechanisms (formation of pits and fatigue cracks) were similar for both the materials, the damage severity was found to be much higher for SS316L steel compared to HEA.
The authors report the development of AlxCoCrFeNi (x = 0.1 to 3) high entropy alloy (HEA) coatings using a simple and straightforward microwave technique. The microstructure of the developed coatings is composed of a cellular structure and diffused interface with the substrate. The microstructure of the HEA coatings varies as a direct function of Al content. An increase in Al fraction shows structural transformation from FCC to BCC along with the evolution of σ and B2 as the major secondary phases. The diffusion of Mo from the substrate enhances the mixing entropy and promotes σ‐phase formation. The HEA coatings show significantly high hardness compared to SS316L substrate steel (227 HV) with a maximum value of 726 HV observed for three‐molar composition. The fracture toughness exhibits an inverse correlation with the Al fraction with the highest value of around 49 MPa m1/2 observed for Al0.1CoCrFeNi coating. The equimolar coating composition shows lowest erosion rates among all the tested samples due to optimum combination of the mechanical properties. The erosion resistance of the equimolar coating is 2 to 5 times higher than steel substrate and around 1.5 times higher than the non‐equimolar counterparts depending upon the impingement angles.
Surface phenomenon such as cavitation erosion-corrosion limits the working life and durability of the fluid machines through significantly altering the efficiency. Surface modification is an apparent and economical route for improving the sustainability of these components. Recently developed complex concentrated alloys (CCAs) or high entropy alloys (HEAs) possess exceptional properties owing to high configurational entropy. We developed CCA coatings on the stainless steel using a facial and effective microwave processing technique. The effect of Al molar fraction in AlCoCrFeNi (x = 0.1-3) CCAs on ultrasonic cavitation erosion-corrosion was investigated in 3.5% NaCl solution. For comparison, cavitation erosion and electrochemical corrosion behavior of the pre- and post-tested samples was also performed. Detailed microstructure and mechanical characterization of the developed coatings were also preformed using different analytical techniques. The equimolar CCA coating showed apical degradation resistance under both pure erosion and erosion-corrosion conditions. The observed behavior is attributed to high strain hardening, optimal hardness, fracture toughness, and utmost stability of the passive layer. The phenomenal conjugation of these properties was associated with highest configurational entropy for equimolar composition resulting in sluggish diffusion, and severe lattice straining. Compared to pits, striations and cracks characterizing the morphology of the degraded stainless steel, the equimolar and AlCoCrFeNi CCAs showed TTS (tearing topograph surface) as the dominant failure mode characterized by presence of microplastic deformation. The degradation of the AlCoCrFeNi CCA occurred mainly through brittle failure mode. The difference in failure mechanism is related to the mechanical properties and underlying microstructure.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.