Iodine and methylene blue adsorption properties of the high surface area nanoporous carbon materials derived from agro-waste and rice husk is reported. Rice husk was pre-carbonized at 300 °C in air followed by leaching out the silica nanoparticles by extraction with sodium hydroxide solution. The silica-free rice husk char was mixed with chemical activating agents sodium hydroxide (NaOH), zinc chloride (ZnCl2), and potassium hydroxide (KOH) separately at a mixing ratio of 1:1 (wt%) and carbonized at 900 °C under a constant flow of nitrogen. The prepared carbon materials were characterized by scanning electron microscopy (SEM), Fourier transformed-infrared spectroscopy (FT-IR), powder X-ray diffraction (pXRD), and Raman scattering. Due to the presence of bimodal micro- and mesopore structures, KOH activated samples showed high specific surface area ca. 2342 m2/g and large pore volume ca. 2.94 cm3/g. Oxygenated surface functional groups (hydroxyl, carbonyl, and carboxyl) were commonly observed in all of the samples and were essentially non-crystalline porous particle size of different sizes (<200 μm). Adsorption study revealed that KOH activated samples could be excellent material for the iodine and methylene blue adsorption from aqueous phase. Iodine and methylene blue number were ca. 1726 mg/g and 608 mg/g, respectively. The observed excellent iodine and methylene blue adsorption properties can be attributed to the well-developed micro- and mesopore structure in the carbon material. This study demonstrates that the agricultural waste, rice husk, and derived nanoporous carbon materials would be excellent adsorbent materials in water purifications.
We have investigated the textural properties, electrochemical supercapacitances and vapor sensing performances of bamboo-derived nanoporous carbon materials (NCM). Bamboo, an abundant natural biomaterial, was chemically activated with phosphoric acid at 400 °C and the effect of impregnation ratio of phosphoric acid on the textural properties and electrochemical performances was systematically investigated. Fourier transform-infrared (FTIR) spectroscopy confirmed the presence of various oxygen-containing surface functional groups (i.e. carboxyl, carboxylate, carbonyl and phenolic groups) in NCM. The prepared NCM are amorphous in nature and contain hierarchical micropores and mesopores. Surface areas and pore volumes were found in the range 218–1431 m2 g−1 and 0.26–1.26 cm3 g−1, respectively, and could be controlled by adjusting the impregnation ratio of phosphoric acid and bamboo cane powder. NCM exhibited electrical double-layer supercapacitor behavior giving a high specific capacitance of c.256 F g−1 at a scan rate of 5 mV s−1 together with high cyclic stability with capacitance retention of about 92.6% after 1000 cycles. Furthermore, NCM exhibited excellent vapor sensing performance with high sensitivity for non-aromatic chemicals such as acetic acid. The system would be useful to discriminate C1 and C2 alcohol (methanol and ethanol).
Nanoporous activated carbons (AC) have been prepared from low-cost agro-waste corncob powder by phosphoric acid activation and investigated for their electrochemical supercapacitor and sensing properties. Surface areas and pore volumes are found in the range of 690–1288 m2 g−1 and 0.49–1.64 cm3 g−1, respectively and could be controlled by adjusting the weight ratio of corncob and phosphorous. The corncob-derived AC showed excellent electrochemical performance giving a maximum specific capacitance ca. 340.8 F g−1 at a scan rate of 5 mV s−1. At relatively a high scan rate of 100 mV s−1 the specific capacitance of 133.7 F g−1 was obtained. About 96% capacitance retention rate was achieved even after 1000 cycles demonstrating potential usages of the materials in high-performance supercapacitor electrodes. Furthermore, our AC showed excellent solvent vapor sensing performance with high selectivity for ammonia.
Nanoporous activated carbon materials derived from agro-wastes could be suitable low-cost electrode materials for high-rate performance electrochemical supercapacitors. Here we report high surface area nanoporous carbon materials derived from Lapsi seed agro-waste prepared by zinc chloride (ZnCl2) activation at 700 °C. Powder X-ray diffraction (pXRD) and Raman scattering confirmed the amorphous structure of the resulting carboniferous materials, which also incorporate oxygen-containing functional groups as confirmed by Fourier transform infrared (FTIR) spectroscopy. Scanning and transmission electron microscopy (SEM and TEM) analyses revealed the granular, nanoporous structures of the materials. High-resolution TEM (HR-TEM) confirmed a graphitic carbon structure containing interconnected mesopores. Surface areas and pore volumes of the materials were found, respectively, in the ranges from 931 to 2272 m2 g−1 and 0.998 to 2.845 cm3 g−1, and are thus superior to commercially available activated carbons. High surface areas, large pore volumes and interconnected mesopore structures of these Lapsi seed-derived nanoporous carbon materials lead to their excellent electrochemical supercapacitance performance in aqueous electrolyte (1 M H2SO4) with a maximum specific capacitance of 284 F g−1 at a current density of 1 A g−1. Furthermore, the electrodes showed high-rate capability sustaining 67.7% capacity retention even at high current density of 20 A g−1 with excellent cycle stability achieving 99% capacitance retention even after 10,000 charge–discharge cycles demonstrating the potential of Lapsi seed derived nanoporous carbons as suitable electrode materials in high-performance supercapacitor devices.
Paracetamol with 1-napthol or resorcinol gave azodye and the concentration of paracetamol was investigated spectrophotometrically. The azodyes formed with both 1-napthol and resorcinol as coupling agents follow Lambert Beer's law in the range of 0 to 10 µgmL-1 of paracetamol. The molar absorptivity and Sandell's sensitivity for azodye coupled with 1-napthol were found to be 1.68×104 Lmol-1cm-1 and 9.0 ngmL-1cm-2, respectively. The molar absorptivity and Sandell's sensitivity for azodye coupled with resorcinol were found to be 2.86×104 Lmol-1cm-1 and 5.3 ngmL-1cm-2, respectively. Both coupling agents had been applied successfully in the analysis of paracetamol in pharmaceutical preparation. The relative standard deviation for all five samples ranged from 2.2-6.4% at 95% confidence. The percentage recoveries were found to range from 97.8 to 103.4. Both methods used in the present study may be applied to the determination of trace amount of paracetamol in different clinical samples. Keyword: Paracetamol; Spectrophotometric; 1-napthol; Resorcinol DOI: 10.3126/jncs.v24i0.2389 Journal of Nepal Chemical Society Vol. 24, 2009 Page: 39-44
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.