Two- and three-dimensional modal and non-modal instability mechanisms of steady spanwise-homogeneous laminar separated flow over airfoil profiles, placed at large angles of attack against the oncoming flow, have been investigated using global linear stability theory. Three NACA profiles of distinct thickness and camber were considered in order to assess geometry effects on the laminar–turbulent transition paths discussed. At the conditions investigated, large-scale steady separation occurs, such that Tollmien–Schlichting and cross-flow mechanisms have not been considered. It has been found that the leading modal instability on all three airfoils is that associated with the Kelvin–Helmholtz mechanism, taking the form of the eigenmodes known from analysis of generic bluff bodies. The three-dimensional stationary eigenmode of the two-dimensional laminar separation bubble, associated in earlier analyses with the formation on the airfoil surface of large-scale separation patterns akin to stall cells, is shown to be more strongly damped than the Kelvin–Helmholtz mode at all conditions examined. Non-modal instability analysis reveals the potential of the flows considered to sustain transient growth which becomes stronger with increasing angle of attack and Reynolds number. Optimal initial conditions have been computed and found to be analogous to those on a cascade of low pressure turbine blades. By changing the time horizon of the analysis, these linear optimal initial conditions have been found to evolve into the Kelvin–Helmholtz mode. The time-periodic base flows ensuing linear amplification of the Kelvin–Helmholtz mode have been analysed via temporal Floquet theory. Two amplified modes have been discovered, having characteristic spanwise wavelengths of approximately 0.6 and 2 chord lengths, respectively. Unlike secondary instabilities on the circular cylinder, three-dimensional short-wavelength perturbations are the first to become linearly unstable on all airfoils. Long-wavelength perturbations are quasi-periodic, standing or travelling-wave perturbations that also become unstable as the Reynolds number is further increased. The dominant short-wavelength instability gives rise to spanwise periodic wall-shear patterns, akin to the separation cells encountered on airfoils at low angles of attack and the stall cells found in flight at conditions close to stall. Thickness and camber have quantitative but not qualitative effect on the secondary instability analysis results obtained.

No abstract

No abstract

No abstract

No abstract

A simple way to decrease the drag and oscillating lift forces in the flow around a circular cylinder consists of positioning a splitter plate in the wake, parallel to the flow. In this paper, the effect of the splitter plate on the wake dynamics, more specifically on the wake transition, is described in detail. First, two-dimensional and three-dimensional direct numerical simulations (DNS) using the spectral element method were used to observe the behaviour of the wake in the presence of the splitter plate. Then, a linear stability analysis based on the Floquet theory was performed in order to obtain information on how the splitter plate changes the instabilities that lead to wake transition. Simulations were carried out for several gaps between the splitter plate and the cylinder, with the Reynolds number varying in the range between 100 and 350, which corresponds to the wake transition in the flow around a circular cylinder. The results of the simulations showed a discontinuity in the Strouhal number curve that is consistent with the results available in the literature. The stability analysis showed how the splitter plate modifies the transition of the flow to a three-dimensional configuration. The splitter plate has a stabilizing effect on the flow for small gaps, delaying the appearance of three-dimensional structures to higher Reynolds numbers. Mode A and a quasi-periodic (QP) mode are observed for such small gaps. As the gap is increased the discontinuity in the Strouhal number curve also caused a clear change in the characteristics of the neutral stability curve, and the existence of an unstable period-doubling mode was observed. The onset characteristics of the unstable modes are analysed and discussed in depth.

SeismicMesh is a Python package for simplex mesh generation in two or three dimensions. As an implementation of DistMesh (Persson & Strang, 2004), it produces high-quality meshes at the expense of speed. For increased efficiency, the core package is written in C++, works in parallel, and uses the Computational Geometry Algorithms Library (Hert & Seel, 2020). SeismicMesh can also produce mesh-density functions from seismological data to be used in the mesh generator.

No abstract