Advancing climate change is affecting the health and vitality of forests in many parts of the world. Europe is currently facing spruce bark beetle outbreaks, which are most often caused by wind disturbances, hot summers, or lack of rainfall and are having a massive economic impact on the forestry sector. The aim of this research article was to summarize current scientific knowledge about the structure and physical and mechanical properties of wood from bark beetle-attacked trees. Spruce stands are attacked by a number of beetles, of which Ips typographus is the most common and widespread in Central Europe. When attacking a tree, bark beetles introduce ophiostomatoid fungi into the tree, which then have a greater effect on the properties of the wood than the beetles themselves. Fungal hyphae grow through the lumina of wood cells and spread between individual cells through pits. Both white rot and brown rot fungi are associated with enzymatic degradation of lignin or holocellulose, which is subsequently reflected in the change of the physical and mechanical properties of wood. Wood-decay fungi that colonize wood after infestation of a tree with bark beetles can cause significant changes in the structure and properties of the wood, and these changes are predominantly negative, in the form of reducing modulus of rupture, modulus of elasticity, discolouration, or, over time, weight loss. In certain specific examples, a reduction in energy consumption for the production of wood particles from beetle-attacked trees, or an increase in surface free energy due to wood infestation by staining fungi in order to achieve better adhesion of paints or glues, can be evaluated positively.
Harvesters produce one third of timber in Czechia. The aim of this study was to analyze the over- and under-bark volume estimates of Scots pine (Pinus sylvestris L.) timber produced by a mid-performance harvester. The data were collected between March 2017 and June 2018. In total, 4661 stems cut into 29,834 logs were analyzed. For volume estimation, StanForD offers several price categories using various algorithms. Three of these price categories are relevant for Czech forestry—M3s, M3toDE, and M3miDE. The M3s price category is based on the estimation of partial volumes of 10 cm long sections, which are summed. Therefore, this price category represents the volume estimation closest to the true volume. By comparison, the M3toDE and M3miDE price categories use the same algorithm for volume estimation, which is based on the Huber formula using a midspan diameter rounded down to the nearest whole centimeter. The M3toDE price category underestimated the over-bark volume by 6.48% compared to the reference price category M3s. The mean log volume estimated through the M3s price category was significantly higher than the M3toDE volume both in individual grades and without grading. We found significant differences between under-bark volume estimates by the diameter band bark deduction method (DBM) and the parametric linear bark deduction method (PLM) used in harvester’s systems according to the Guidelines for Electronic Scaling of Timber for Harvesters in Czechia (GEH) for Scots pine butt logs with rough bark, and also for other logs with normal bark thickness. To obtain under-bark volume estimates of Scots pine timber that are comparable with the Guidelines for Timber Scaling in Czechia (GTS) using the parametric nonlinear bark deduction method (PNM), we recommend using the algorithm of the M3toDE price category, with double bark thickness determined by the diameter band bark deduction method.
Timber is the most important source of revenue in forestry and, therefore, is necessary to precisely estimate its volume. The share of timber volume produced by harvesters is annually growing in many European countries. Suitable settings of harvesters will allow us to achieve the most accurate volume estimates of the produced timber. In this study, we compared the different methods of log volume estimation applied by control and information systems of harvesters. The aim was to analyze the price categories that can be set up in the StanForD standard and to determine the differences between the algorithms used for log volume estimations. We obtained the data from *.STM files collected from March 2017 until June 2018 on a medium-size harvester. We analyzed price categories and found seven different algorithms used to estimate the log volumes. Log volume estimates according to Algorithm A2 were considered as standard because these estimates should be closest to the true log volumes. Significant differences, except the difference between Algorithm A2 and Algorithm A3, were found between log volumes estimated by different algorithms. After categorization of logs to assortments, the results showed that significant differences existed between algorithms in each assortment. In the roundwood assortment, which contains the most valuable logs, a difference of more than 6% was found between the log volumes estimated by Algorithm A5 and Algorithm A2. This is interesting because Algorithm A5 is widely used in some Central European countries. To obtain volumes closest to the true volumes, we should use Algorithm A2 for the harvester production outputs. The resulting differences between the algorithms can be used to estimate the volume difference between harvester outputs using the different price categories. Understanding this setting of harvesters and the differences between the price categories will provide users useful information in applied forest management.
Since 2014, forestry in the Czech Republic has been significantly affected by a bark beetle outbreak. The volume of infested trees has exceeded processing capacity and dead standing spruce (Picea abies) remain in the forest stands, even for several years. What should be done with this bark beetle wood? Is it necessary to harvest it in order to preserve the basic mechanical and physical properties? Is it possible to store it under standard conditions, or what happens to it when it is “stored” upright in the forest? These are issues that interested forest owners when wood prices were falling to a minimum (i.e., in 2018–2019) but also today, when the prices of quality wood in Central European conditions are rising sharply. To answer these questions, we found out how some of the mechanical properties of wood change in dead, bark beetle-infested trees. Five groups of spruce wood were harvested. Each of these groups was left upright in the forest for a specified period of time after bark beetle infestation, and one group was classified as a reference group (uninfested trees). Subsequently, we discovered what changes occurred in tensile and compressive strength depending on the time left in the stand and the distance from the center of the trunk. When selecting samples, we eliminated differences between individual trees using a CT scanning technique, which allowed us to separate samples, especially with different widths of annual rings and other variations that were not caused by bark beetle. The results showed the effect of log age and radial position in the trunk on tensile and compressive strength. The values for tensile strength in 3-year infested trees decreased compared to uninfested trees by 14% (from 93.815 MPa to 80.709 MPa); the values for compressive strength then decreased between the same samples by up to 25.6% (from 46.144 MPa to 34.318 MPa). A significant decrease in values for compressive strength was observed in the edges of the trunks, with 44.332 MPa measured in uninfested trees and only 29.750 MPa in 3-year infested trees (a decrease of 32.9%). The results suggest that the use of central timber from bark beetle-infested trees without the presence of moulds and fungi should not be problematic for construction purposes.
Cut-to-length (CTL) operations are expanding in Central European bio-economies. However, they are costly, so efficiency must be maximized. The objective of this study was to analyze direct operational costs of three forwarders from the year 2006 until 2019. Annual amortization, services, materials, and personnel costs were analyzed and compared through ANOVA, trends were analyzed through linear regression. Forwarders LVS 5, John Deere 1010, and John Deere 1110E were deployed in coniferous forest stands with a mean stem volume between 0.10 and 0.84 m3/stem, forwarding distance between 261 and 560 m. The machines forwarded between 4045 and 34,604 m3 of timber per year, over operational times between 490 and 3896 MH (machine hours)/year, reaching machine utilization between 58% and 89%, machine productivity between 3.5 and 12.3 m3/MH, and costs between 20.95 and 84.39 €/MH. The most substantial were personnel costs (35 to 66% of the total costs), followed by materials (14.9–27.1%), amortization (12.5–15.7%), and services (3.3–22.1%). Differences between total operational costs per m3 of machines with different engine powers were not observed.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.