No abstract

No abstract

No abstract

No abstract

The VIVACE converter was introduced at OMAE2006 as a single, smooth, circular-cylinder module. The hydrodynamics of VIVACE is being improved continuously to achieve higher density in harnessed hydrokinetic power. Intercylinder spacing and passive turbulence control (PTC) through selectively located roughness are effective tools in enhancement of flow induced motions (FIMs) under high damping for power harnessing. Single cylinders harness energy at high density even in 1 knot currents. For downstream cylinders, questions were raised on energy availability and sustainability of high-amplitude FIM. Through PTC and intercylinder spacing, strongly synergetic FIMs of 2/3/4 cylinders are achieved. Twocylinder smooth/PTC, and three/four-cylinder PTC systems are tested experimentally. Using the "PTC-to-FIM" map developed in previous work at the Marine Renewable Energy Laboratory (MRELab), PTC is applied and cylinder response is measured for inflow center-tocenter distance 2D-5D (D = diameter), transverse center-to-center distance 0. Ree[28,000], m*e[1.677-1.690], Ue[0.36-1.45 m/s], aspect ratio l/D = 10.29, and m*[, e [0.0283-0.0346]. All experiments are conducted in the low turbulence free surface water (LTFSW) channel of MRELab. Amplitude spectra and broad field-of-view (FOV) visualization help reveal complex flow structures and cylinder interference undergoing VN, interference/ proximity/wake/soft/hard galloping. FIM amplitudes of 2.2-2.8D are achieved for all cylinders in steady flow for all parameter ranges tested.

A passive control means to suppress flow-induced motions (FIM) of a rigid circular cylinder in the TrSL3, high-lift, flow regime is formulated and tested experimentally. The developed method uses passive turbulence control (PTC) consisting of selectively located roughness on the cylinder surface with thickness about equal to the boundary layer thickness. The map of "PTC-to-FIM," developed in previous work, revealed robust zones of weak suppression, strong suppression, hard galloping, and soft galloping. PTC has been used successfully to enhance FIM for hydrokinetic energy harnessing using the VIVACE Converter. PTC also revealed the potential to suppress FIM to various levels. The map is flow-direction dependent. In this paper, the "PTC-to-FIM" map is used to guide development of FIM suppression devices that are flow-direction independent and hardly affect cylinder geometry. Experiments are conducted in the Low Turbulence Free Surface Water Channel of the University of Michigan on a rigid, horizontal, circular cylinder, suspended on springs. Amplitude and frequency measurements and broad field-of-view visualization reveal complex flow structures and their relation to suppression. Several PTC designs are tested to understand the effect of PTC roughness, location, coverage, and configuration. Gradual modification of PTC parameters, leads to improved suppression and evolution of a design reducing the VIV synchronization range. Over a wide range of high reduced velocities, VIV is fully suppressed. The maximum amplitude occurring near the system's natural frequency is reduced by about 63% compared to the maximum amplitude of the smooth cylinder.

No abstract

A passive control means to suppress flow-induced motions (FIM) of a rigid circular cylinder in the TrSL3, high-lift, flow regime is formulated and tested experimentally. The method developed uses passive turbulence control (PTC) consisting of selectively located roughness on the cylinder surface with thickness about equal to the boundary layer thickness. The map of “PTC-to-FIM”, developed in previous work, revealed robust zones of weak suppression, strong suppression, hard galloping, and soft galloping. PTC has been used successfully to enhance FIM for hydrokinetic energy harnessing using the VIVACE Converter. The same technology revealed the potential to suppress FIM to various levels. The map is flow-direction dependent. In this paper, the “PTC-to-FIM” map is used to guide development of FIM suppression devices that are flow-direction independent and hardly affect cylinder geometry. Experiments are conducted in the Low Turbulence Free Surface Water Channel of the University of Michigan on a rigid, horizontal, circular cylinder, suspended on springs. Amplitude and frequency measurements and broad field-of-view visualization reveal complex flow structures and their relation to suppression. Several PTC designs are tested to understand PTC direction, roughness, thickness, and coverage. Gradual modification of PTC parameters, leads to improved suppression and evolution of a design reducing the VIV synchronization range, fully suppressing VIV in a wide range, and reducing the maximum occurring near the system’s natural frequency by about 60% compared to the maximum amplitude of the smooth cylinder.