Solid-gas coupling coal-like materials are essential for simulating coal and gas outbursts and the long-term safety study of CO2 sequestration in coal. However, reported materials still differ substantially from natural coal in mechanical, deformation and gaseous properties; the latter two aspects are common not considered. There is a lack of a definite and quantitative preparation method of coal-like materials with high similarity for future reference. Here, 25 groups of raw material ratios were designed in the orthogonal experiment using uniaxial compression, shearing and adsorption/desorption tests. Experiment results indicated that the coal-like materials were highly similar to soft coals in properties mentioned above. And range analysis revealed the key influencing factors of each mechanical index. The gypsum/petrolatum ratio controls the density, compressive strength, elastic modulus, cohesion and deformation characteristic. The coarse/fine coal powder (1–2 and 0–0.5 mm) controls the internal friction angle and is the secondary controlling factor for compressive strength and elastic modulus. The effect of coal particle size on the sample strength was studied using scanning electron microscope (SEM). When the gypsum/petrolatum ratio increased, the deformation characteristics changed from ductile to brittle. The different failure modes in the samples were revealed. The coal powder content is a key in the gas adsorption/desorption properties and an empirical formula for estimating the adsorption capacity was established. Based on the range analysis of experimental results, a multiple linear regression model of the mechanical parameters and their key influencing factors was obtained. Finally, a composition closely resembling the natural coal was determined, which differs by only 0.47–7.41% in all parameters except porosity (11.76%). Possible improvements and extension to similar materials are discussed. The findings of this study can help for better understanding of coal and gas outburst mechanism and stability of CO2 sequestration in soft coal seams.
Zonal disintegration, a phenomenon of fractured zones and intact zones distributed alternately in deep rock mass, is different from the excavation-damaged zone of shallow rock mass. In this study, bonded block model of 3DEC was employed to study the fracture mode and origination condition of zonal disintegration. Initiation, propagation, and coalescence progress of fracture around the roadway boundary under different triaxial stress conditions are elaborated. Numerical simulation demonstrated that zonal disintegration may occur when the direction of maximum principal stress is parallel to the roadway axis. It is interesting to find that the fracture around the roadway boundary traced the line of a spiral line, while slip-line fractures distributed apart from the roadway boundary. The extent of the alternate fracture zone decreased as the confining pressure increased, and alternate fracture zone was no longer in existence when the confining pressure reaches a certain value. Effects of roadway shape on zonal disintegration were also studied, and the results indicated that the curvature of the fracture track line tends to be equal to the roadway boundary in shallow surrounding rock of the roadway, while the fractures in deep surrounding rock seems unaffected by the roadway shape. Those findings are of great significance to support design of deep underground openings.
The acoustic emission, energy, and damage evolution of coal samples for three kinds of uniaxial cyclic loading and unloading are deeply analyzed in this study. The evolution of total absorption energy, elastic strain energy, and dissipated energy of coal samples is related to the stress path, and the increasing amplitudes cycle loading has an obvious damage effect on coal samples. During the loading stage, the acoustic emission phenomenon is most active when loading is increasing and the Felicity and post-Kaiser phenomena appear. The acoustic emission phenomenon during constant loading does not obviously change, but rather becomes active with the increase of the equivalent load. The damage to the coal sample shows nonlinear change increasing loading and unloading and shows linear change for other stress paths. Compared to waveforms with stepwise increasing amplitudes cyclic loading, the failure process of the coal sample is more closely related to the size of the external load, which indicates that reasonable hydraulic design is beneficial to the stability of the confining pressure in the chamber of an underground pumped storage hydropower station.
The fracture development and distribution around the deep soft rock roadway are pivotal to any underground design. In this paper, both field investigation and numerical simulation were taken to study the fracture evolution and rock deformation of a coal mine roadway at Kouzidong mine, Fuyang, Anhui Province, China. Based on the borehole imaging technique, we found an asymmetric distribution of the fracture zone in the surrounding rock of the roadway. By analyzing the C value of the fractures in the borehole images,we found that the fracture interval distribution of the surrounding rock of the tunnel, the number of fractures will fluctuate decrease with the increase of the depth. To effectively study the fracture propagation and distribution of the roadway under longwall retreatment and roadway excavation, the global-local numerical technique was applied via FLAC3D and PFC2D. In the roadway excavation process, fractures were first formed in the shallow section of the roadway and progressively propagated toward the deeper soft rock layer; the main failure mechanism was a tensile failure. During longwall retreatment, fractures continuously developed toward the deeper soft rock layer. However, the failure mechanism transformed to shear failure. From numerical results, it can be seen that the stress concentration at the ribs was released, which led to shear failure at the roof and floor. Due to the extensive tensile cracks in the shallow section, the surrounding rock experienced expansion and fracture. The deep shear failure also induced the formation of the nonadjacent crushing zone and elastic zone, which is in line with the borehole imaging results.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.