Hydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of bearing pads, which significantly change oil gap geometry, and in consequence, decreases bearing load-carrying ability. Design of hydrodynamic thrust bearing of large dimensions seems to be a demanding engineering challenge, and additional difficulty comes from limited possibilities of experimental testing of these systems due to high costs. Theoretical investigations, carried out with the use of specially developed computer models, remain a feasible alternative for experimental research. But the accuracy of the models is not often directly validated, because of the lack of appropriate experimental data coming from large objects. In this paper, results of calculations carried out for a large hydrodynamic thrust bearing are shown and compared to measurement data obtained at bearing commissioning stage. Pad temperatures profile sliding surface, oil pressure in hydrodynamic gap and film geometry are compared to the measured values. According to the presented comparisons, some conclusions are drawn with respect to the accuracy of models used to predict large thrust bearing performance.
The start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient simulation of the bearing start-up. A bidirectional bearing of a pump-storage power plant is investigated. To show the potential advantages of the new method, a comparison of the warm and cold start procedure is presented. The thermal crowning of the bearing pad, oil film gap and other parameters of both cases are compared in this article.
Large thrust bearings are highly loaded machine elements and their failures cause serious losses. Start ups and stoppages of the bearing under load are specially critical regimes of operation. Load carrying capacity depends on the profile of the oil gap. In transient states this profile is also changing. In the design of large thrust bearings minimizing thermo-elastic deformations is an important goal, which can be accomplished due to application of advanced models of the bearing. Modeling of transient states becomes even more complex since there is a dynamic development of temperature distribution and deformations. Often hydrostatic jacking systems are also used. It seems to the authors that advanced bearing models are applied only in research and development of the bearings while very simple modeling is applied in on-line analysis of data from monitoring systems. Analysis of the measurement data with the use of more sophisticated models may be helpful in assessment of current bearing status -especially in early warning. Material issues create a separate problem for modeling, being more important nowadays as polymer lined bearings come into use. The models used for polymer lined bearings require realistic treatment of heat exchange and resilience of the bearing surface layer.
Hydro generators installed in Itaipu Binacional power plant with 824/737 MVA rated output power (50/60 Hz) belong to the largest ones in the world. Among many unique features, the generators are equipped with the largest hydrodynamic thrust bearings ever built (external diameter 5,200 mm, axial load equals approximately 3,600 t). This paper is an attempt to propose a new thrust bearing design with the use of the state-of-the-art technologies and simulation techniques that demonstrate a reduction of friction power losses generated by the thrust bearing. This paper is divided into two parts. Within the first one, the original thrust bearing design which was implemented in the generators is described. Related calculation results based on a TEHD (thermo-elasto-hydrodynamic) calculation software used by Alstom will be presented. A comparison between measurement results gathered in the 1980s is given. In the second part, a potential solution of a more beneficial bearing design is described. The proposed thrust bearing design modification is an implementation of Alstom's Polypad TM coating. This modern polymer (PEEK) coating material has already been used by Alstom in projects around the world for many years. This coating allows pushing the operating parameters limits toward higher temperatures and lower oil film thicknesses far beyond the limits known for the conventional bearing materials.
Hydro generators installed in Itaipu Binacional power plant with 824/737 MVA rated output power (50/60 Hz) belong to the largest ones in the world. Among many unique features the generators are equipped with the largest hydrodynamic thrust bearings ever built (external diameter 5200 mm, axial load equals approximately 3600 t). This paper is an attempt to propose a new thrust bearing design with the use of the stateof-the-art technologies and simulation techniques that demonstrate a reduction of friction power losses generated by the thrust bearing. This paper is divided into two parts. Within the first one the original thrust bearing design which was implemented in the generators is described. Related calculation results based on a thermo-elastohydrodynamic (TEHD) calculation software used by Alstom will be presented. A comparison between measurement results gathered in the 1980's is given. In the second part a potential solution of a more beneficial bearing design is described. The proposed thrust bearing design modification is an implementation of Alstom's Polypad TM coating. This modern polymer (PEEK) coating material has already been used by Alstom in projects around the world for many years. This coating allows pushing the operating parameters limits toward higher temperatures and lower oil film thicknesses far beyond the limits known for the conventional bearing materials.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.