Transtibial (TT) amputations, or below-knee amputations, are among the most frequently performed major limb removals. To replace the missing limb, numerous prosthetic devices were developed. A study of the state-of-the-art in TT prostheses shows that none of the commercially available devices are capable of mimicking an able-bodied ankle-foot complex. Still on a research level, some powered prosthetic devices have the potential to improve amputee walking experience, but still need heavy and bulky actuators to provide the necessary power of propulsion. With the AMP-Foot 2.0, the authors propose a new concept for an energy efficient, powered transtibial prosthesis. Its design enables the use of a low power actuator which stores energy in springs during the complete stance phase that can be released at push-off. Thanks to this, the size and weight of the actuator can be decreased considerably while the ankle still provides the full power necessary for forward propulsion. A prototype of the AMP-Foot 2.0 has been built and experiments with a transfemural amputee were conducted. The captured data is presented and analyzed throughout this paper.

Locking devices are widely used in robotics, for instance to lock springs, joints or to reconfigure robots. This review paper classifies the locking devices currently described in literature and preforms a comparative study. Designers can, as such, better determine which locking device best matches the needs of their application. The locking devices are divided into three main categories based on different locking principles: mechanical locking, friction-based locking and singularity locking. Different lockers in each category can be passive lockers or active lockers. Based on an elaborate literature study, the paper summarizes the findings by comparing different locking devices, based on a set of properties of a theoretical ideal locking device.

Throughout the last decade, a whole new generation of powered transtibial prostheses and exoskeletons has been developed. However, these technologies are limited by a gait phase detection which controls the wearable device as a function of the activities of the wearer. Consequently, gait phase detection is considered to be of great importance, as achieving high detection accuracy will produce a more precise, stable, and safe rehabilitation device. In this paper, we propose a novel gait percent detection algorithm that can predict a full gait cycle discretised within a 1% interval. We called this algorithm an exponentially delayed fully connected neural network (ED-FNN). A dataset was obtained from seven healthy subjects that performed daily walking activities on the flat ground and a 15-degree slope. The signals were taken from only one inertial measurement unit (IMU) attached to the lower shank. The dataset was divided into training and validation datasets for every subject, and the mean square error (MSE) error between the model prediction and the real percentage of the gait was computed. An average MSE of 0.00522 was obtained for every subject in both training and validation sets, and an average MSE of 0.006 for the training set and 0.0116 for the validation set was obtained when combining all subjects’ signals together. Although our experiments were conducted in an offline setting, due to the forecasting capabilities of the ED-FNN, our system provides an opportunity to eliminate detection delays for real-time applications.

Despite the increased interest in exoskeleton research in the last decades, not much progress has been made on the successful reduction of user effort. In humans, biarticular elements have been identified as one of the reasons for the energy economy of locomotion. This document gives an extensive literature overview concerning the function of biarticular muscles in human beings. The exact role of these muscles in the efficiency of human locomotion is reduced to three elementary functions: energy transfer towards distal joints, efficient control of output force direction and double joint actuation. This information is used to give an insight in the application of biarticular elements in bio-inspired robotics, i.e. bipedal robots, exoskeletons, robotic manipulators and prostheses. Additionally, an attempt is made to find an answer on the question whether the biarticular property leads to a unique contribution to energy efficiency of locomotion, unachievable by mono-articular alternatives. This knowledge is then further utilised to indicate how biarticular actuation of exoskeletons can contribute to an increased performance in reducing user effort.

No abstract

In the past decades, researchers have deeply studied pathological and nonpathological gait to understand the human ankle function during walking. These efforts resulted in the development of new lower limb prosthetic devices aiming at raising the 3C-level (control, comfort, and cosmetics) of amputees. Thanks to the technological advances in engineering and mechatronics, challenges in the field of prosthetics have become an important source of interest for roboticists. Currently, most of the bionic feet are still on a research level but show promising results and a preview of tomorrow's commercial prosthetic devices. In this paper, the authors present the current state-of-the-art and the latest advances in propulsive bionic feet with its actuation principles. The context of this review study is outlined followed by a brief description of the basics in human biomechanics and criteria for new prosthetic designs. A new categorization based on the actuation principle of propulsive ankle-foot prostheses is proposed. Based on simulations, the general principles and benefits of each actuation method are explained. The corresponding latest advances in propulsive bionic feet are presented together with their main characteristics and scientific outcomes. The authors also propose to the reader a comparison analysis of the presented devices with a discussion of the general tendencies in new prosthetic feet.

The Ankle Mimicking Prosthetic (AMP-) Foot 2 is a new energy efficient, powered transtibial prosthesis mimicking intact ankle behavior. The author's research is focused on the use of a low power actuator which stores energy in springs during the complete stance phase. At push-off, this energy can be released hereby providing propulsion forces and torques to the amputee. With the use of the so-called catapult actuator, the size and weight of the drive can be decreased compared to state-of-the-art powered prostheses, while still providing the full power necessary for walking.In this article, the authors present a detailed description of the catapult actuator followed by a comparison with existing actuator technology in powered prosthetic feet with regard to torque and power requirements. The implication on the actuator's design will then be outlined. Further, a description of the control strategy behind the AMP-Foot 2 and 2.1 will be given. In the last section of the article, the actuation principle and control are illustrated by experimental validation with a transfemoral amputee. Conclusions and future work complete the paper.

The majority of the commercial transtibial prostheses are purely passive devices. They store energy in an elastic element during the beginning of a step and release it at the end. A 75 kg human, however, produces on average 26 J of energy during one stride at the ankle joint when walking at normal cadence and stores/releases 9 J of energy, contributing to energy efficient locomotion. According to Winter, a subject produces on average of 250W peak power at a maximum joint torque of 125 Nm. As a result, powering a prosthesis with traditional servomotors leads to excessive motors and gearboxes at the outer extremities of the legs. Therefore, research prototypes use series elastic actuation (SEA) concepts to reduce the power requirements of the motor. In the paper, it will be shown that SEAs are able to reduce the power of the electric motor, but not the torque. To further decrease the motor size, a novel human-centered actuator concept is developed, which is inspired by the variable recruitment of muscle fibers of a human muscle. We call this concept series-parallel elastic actuation (SPEA), and the actuator consists of multiple parallel springs, each connected to an intermittent mechanism with internal locking and a single motor. As a result, the motor torque requirements can be lowered and the efficiency drastically increased. In the paper, the novel actuation concept is explained, and a comparative study between a stiff motor, an SEA and an SPEA, which all aim at mimicking human ankle behavior, is performed