The light-driven sodium-pumping rhodopsin KR2 from Krokinobacter eikastus is the only nonproton cation active transporter with demonstrated potential for optogenetics. However, the existing structural data on KR2 correspond exclusively to its ground state, and show no sodium inside the protein, which hampers the understanding of sodium-pumping mechanism. Here we present crystal structure of the O-intermediate of the physiologically relevant pentameric form of KR2 at the resolution of 2.1 Å, revealing a sodium ion near the retinal Schiff base, coordinated by N112 and D116 of the characteristic NDQ triad. We also obtained crystal structures of D116N and H30A variants, conducted metadynamics simulations and measured pumping activities of putative pathway mutants to demonstrate that sodium release likely proceeds alongside Q78 towards the structural sodium ion bound between KR2 protomers. Our findings highlight the importance of pentameric assembly for sodium pump function, and may be used for rational engineering of enhanced optogenetic tools.

<div> <div> <p>The emergence of the 2019 novel coronavirus (COVID-19), for which there is no vaccine or any known effective treatment created a sense of urgency for novel drug discovery approaches. One of the most important COVID-19 protein targets is the 3C-like protease for which the crystal structure is known. Most of the immediate efforts are focused on drug repurposing of known clinically-approved drugs and virtual screening for the molecules available from chemical libraries that may not work well. For example, the IC50 of lopinavir, an HIV protease inhibitor, against the 3C-like protease is approximately 50 micromolar, which is far from ideal. In an attempt to address this challenge, on January 28th, 2020 Insilico Medicine decided to utilize a part of its generative chemistry pipeline to design novel drug-like inhibitors of COVID-19 and started generation on January 30th. It utilized three of its previously validated generative chemistry approaches: crystal-derived pocked-based generator, homology modelling-based generation, and ligand-based generation. Novel druglike compounds generated using these approaches were published at <a href="http://www.insilico.com/ncov-sprint/">www.insilico.com/ncov-sprint/</a>. Several molecules will be synthesized and tested using the internal resources; however, the team is seeking collaborations to synthesize, test, and, if needed, optimize the published molecules. <br></p> </div> </div>

Amphiphilic copolymers composed of styrene and maleic acid (SMA) monomers caused a major methodical breakthrough in the study of membrane proteins. They were found to directly release phospholipids and membrane proteins both from artificial and natural lipid bilayers, yielding stable water-soluble discoidal SMA/lipid particles (SMALPs) of uniform size. Although many empirical studies indicate the great potency of SMALPs for membrane protein research, the mechanisms of their formation remain obscure. It is unknown which factors account for the very assembly of SMALPs and govern their uniform size. We have developed a coarse-grained (CG) molecular model of SMA copolymers based on the MARTINI CG force field and used it to probe the behavior of SMA copolymers with varying composition/charge/concentration in solution as well as their interaction with lipid membranes. First, we found that SMA copolymers tend to aggregate in solution into clusters, which could account for the uniform size of SMALPs. Next, molecular dynamics (MD) simulations showed that periodic SMA copolymers with styrene/maleic acid ratios of 2:1 ([SSM] n ) and 3:1 ([SSSM] n ) differently interacted with lipid bilayers. While clusters of 2:1 SMA copolymers induced membrane poration, the clusters of 3:1 SMA copolymers extracted lipid patches from the membrane yielding SMALP-like structures. Extraction of lipid patches was also observed when we simulated the behavior of 3:1 copolymers with varying lengths and statistical distribution of styrene and MA units. Analysis of MD simulation trajectories and comparison with experimental data indicate that the formation of SMALPs requires copolymer molecules with a sufficient number of units made of more than two sequential styrene monomers.

Thirteen tubulin protofilaments, made of αβ-tubulin heterodimers, interact laterally to produce cytoskeletal microtubules. Microtubules exhibit the striking property of dynamic instability, manifested in their intermittent growth and shrinkage at both ends. This behavior is key to many cellular processes, such as cell division, migration, maintenance of cell shape, etc. Although assembly and disassembly of microtubules is known to be linked to hydrolysis of a guanosine triphosphate molecule in the pocket of β-tubulin, detailed mechanistic understanding of corresponding conformational changes is still lacking. Here we take advantage of the recent generation of in-microtubule structures of tubulin to examine the properties of protofilaments, which serve as important microtubule assembly and disassembly intermediates. We find that initially straight tubulin protofilaments, relax to similar non-radially curved and slightly twisted conformations. Our analysis further suggests that guanosine triphosphate hydrolysis primarily affects the flexibility and conformation of the inter-dimer interface, without a strong impact on the shape or flexibility of αβ-heterodimer. Inter-dimer interfaces are significantly more flexible compared to intra-dimer interfaces. We argue that such a difference in flexibility could be key for distinct stability of the plus and minus microtubule ends. The higher flexibility of the inter-dimer interface may have implications for development of pulling force by curving tubulin protofilaments during microtubule disassembly, a process of major importance for chromosome motions in mitosis.