For two series of polyethylenimine-graft-poly(ethylene glycol) (PEI-g-PEG) block copolymers, the influence of copolymer structure on DNA complexation was investigated and physicochemical properties of these complexes were compared with the results of blood compatibility, cytotoxicity, and transfection activity assays. In the first series, PEI (25 kDa) was grafted to different degrees of substitution with PEG (5 kDa) and in the second series the molecular weight (MW) of PEG was varied (550 Da to 20 kDa). Using atomic force microscopy, we found that the copolymer block structure strongly influenced the DNA complex size and morphology: PEG 5 kDa significantly reduced the diameter of the spherical complexes from 142 +/- 59 to 61 +/- 28 nm. With increasing degree of PEG grafting, complexation of DNA was impeded and complexes lost their spherical shape. Copolymers with PEG 20 kDa yielded small, compact complexes with DNA (51 +/- 23 nm) whereas copolymers with PEG 550 Da resulted in large and diffuse structures (130 +/- 60 nm). The zeta-potential of complexes was reduced with increasing degree of PEG grafting if MW >or= 5 kDa. PEG 550 Da did not shield positive charges of PEI sufficiently leading to hemolysis and erythrocyte aggregation. Cytotoxicity (lactate dehydrogenase assay) was independent of MW of PEG but affected by the degree of PEG substitution: all copolymers with more than six PEG blocks formed DNA complexes of low toxicity. Finally, transfection efficiency of the complexes was studied. The combination of large particles, low toxicity, and high positive surface charge as in the case of copolymers with many PEG 550 Da blocks proved to be most efficient for in vitro gene transfer. To conclude, the degree of PEGylation and the MW of PEG were found to strongly influence DNA condensation of PEI and therefore also affect the biological activity of the PEI-g-PEG/DNA complexes. These results provide a basis for the rational design of block copolymer gene delivery systems.

Two series of block copolymers were prepared by grafting linear poly(ethylene glycol) (PEG) onto branched polyethylenimine (PEI). In the first series, the PEI (25 000) was grafted with varied numbers of PEG blocks (5000). The second series was composed of copolymers all containing an equal amount of PEG (50%) and PEI (50%), but with PEG of different molecular weights (MW:  550−20 000). In a two-step synthesis, both the activation of monomethyl-PEGs and the coupling reactions of the PEGs with PEI were performed with hexamethylene diisocyanate (HMDI), leading to water-soluble copolymers with hydrolytically stable urethane and urea bonds. The molecular structure of the resulting copolymers was evaluated spectroscopically (NMR, FTIR). Thermal and calorimetric analysis (TGA, DSC) as well as size exclusion chromatography (SEC) verified the successful formation of the copolymers. MW was determined by static light scattering in combination with SEC. With respect to their application as gene transfer agents, the biocompatibility of the copolymers was studied using an in vitro cytotoxicity assay (lactate dehydrogenase assay) and blood compatibility tests (hemolysis and erythrocyte aggregation). It was found that PEG reduced the toxicity of PEI and prevented hemolysis as well as the aggregation of erythrocytes. The extent of the positive influence of PEG on the biocompatibility of the copolymers was found to be dependent upon both the number of PEG blocks and the structure of the block copolymers.

No abstract

Different non-ionic cellulose ethers like methyl cellulose (MC), hydroxypropyl cellulose (HPC) and hydroxypropylmethyl cellulose (HPMC) were investigated. The characterization of the cellulose ethers was carried out by thermogravimetry and sorption/desorption isotherms. Differences in the properties of the cellulose ether films were described by time-dependent contact angle measurements. Changes in molecular structure of the raw materials, gels and films caused by water contact were studied using Raman spectroscopy. Differences between the substitution types and changes due to the gel or film formation were observed. An environmental scanning electron microscopy (ESEM) technique was used to distinguish the morphological behaviour of the cellulose ether films in contact with water. Based on in-situ ESEM experiments, the swelling and drying behaviour of the various stages of cellulose ether films (film-hydrated film-dried film) were quantified by using image analysis.

In this study, the effect of powder cellulose (PC) and 2 types of microcrystalline cellulose (MCC 101 and MCC 301) on pellet properties produced by an extrusion/spheronization process was investigated. The different investigated types of cellulose displayed different behavior during the extrusion/spheronization process. Pure PC was unsuitable for extrusion, because too much water was required and the added water was partly squeezed during the extrusion process. In contrast, MCC 101 and MCC 301 were extrudable at a wide range of water content, but the quality of the resulting products varied. In the extrusion/spheronization process, MCC 101 was the best substance, with easy handling and acceptable product properties. The properties of the extrudates and pellets were determined by Fourier transform (FT) Raman spectroscopy and environmental scanning electron microscopy (ESEM). FT-Raman spectroscopy was able to distinguish between the original substances and also between the wet and dried extrudates. The particle sizes of the raw material and of the extrudates were determined by ESEM without additional preparation. For MCC, the size of the resulting particles within the extrudate or pellet was smaller. However, in the extrudates of PC, changes in particle size could not be observed.