Further developments of the previously reported high-speed contact-mode AFM are described. The technique is applied to the imaging of human chromosomes at video rate both in air and in water. These are the largest structures to have been imaged with high-speed AFM and the first imaging in liquid to be reported. A possible mechanism that allows such high-speed contact-mode imaging without significant damage to the sample is discussed in the context of the velocity dependence of the measured lateral force on the AFM tip.

Aim: The effects of gaseous ozone and open air factor (OAF) on environmental Listeria monocytogenes attached to three common food contact surfaces were investigated. Methods and Results: Listeria monocytogenes on different food contact surfaces was treated with ozone and OAF. Microbiological counts, scanning electron microscopy (SEM) and atomic force microscopy (AFM) were performed. Ozone at 10 ppm gave <1-log reduction when L. monocytogenes was attached to stainless steel, while 45 ppm gave a log reduction of 3Á41. OAF gave better log reductions than 10 ppm ozone, but lower log reductions than 45 ppm. Significant differences were found between surfaces. Biofilm organisms were significantly more resistant than those surface attached on stainless steel. SEM and AFM demonstrated different membrane and cell surface modifications following ozone or OAF treatment. Conclusions:The strain used demonstrated higher resistance to ozone than previous studies. This may be due to the fact that it was isolated from a food manufacturing premises that used oxidizing disinfectants. OAF was more effective at reducing the levels of the organism than an ozone concentration of 10 ppm. Significance and Impact of the Study: Pathogen management strategies must account for resistance of environmental strains when validating cleaning and disinfection. OAF has shown potential for surface decontamination compared with ozone. SEM and AFM are valuable tools for determining mechanisms of action of antimicrobial agents.

The gas vesicles of the cyanobacterium Anabaena flos-aquae contain two main proteins: GvpA, which forms the ribs of the hollow cylindrical shell, and GvpC, which occurs on the outer surface. Analysis by MALDI-TOF MS shows that after incubating Anabaena gas vesicles in trypsin, GvpA was cleaved only at sites near the N-terminus, whereas GvpC was cleaved at most of its potential tryptic sites. Many of the resulting tryptic peptides from GvpC remained attached to the underlying GvpA shell: the pattern of attachment indicated that there are binding sites to GvpA at both ends of the 33-residue repeats (33RRs) in GvpC, although one of the tryptic peptides within the 33RR did not remain attached. Tryptic peptides near the two ends of the GvpC molecule were also lost. The mean critical collapse pressure of Anabaena gas vesicles decreased from 0.63 MPa to 0.20 MPa when GvpC was removed with urea or fully digested with trypsin; partial digestion resulted in partial decrease in critical pressure.

In cyanobacteria the protein on the outside of the gas vesicle, GvpC, is characterised by the presence of a 33 amino acid residue repeat (33RR), which in some genera is highly conserved. The number of 33RRs correlates with the diameter of the gas vesicle and inversely with its strength. Gas vesicles isolated from Microcystis aeruginosa strain PCC 7806 were found to be wider and have a lower critical collapse pressure than those from Microcystis sp. strain BC 8401. The entire gas-vesicle gene cluster of the latter strain was sequenced and compared with the published sequence of the former: the sequences of nine of the ten gvp genes differed by only 1-5% between the two strains; the only substantial difference was in gvpC which in strain BC 8401 lacked a 99-nucleotide section encoding a 33RR. This observation further narrows the correlation of gas vesicle width to the number of 33RRs and suggests how Microcystis strains might be used in experimental manipulation of gas vesicle width and strength.

NaF, pH 7) prior to addition of the acid; the speed of dissolution for these samples was much less than that of the untreated samples. The HS AFM used an in-house designed and constructed high-speed flexure scan stage employing a push-pull piezo actuator arrangement. The HS AFM is able to follow the large changes in height (on the micrometer scale) that occur during the dissolution process.