The current floating bridge concepts of Norwegian Public Roads Administration (Statens vegvesen, NPRA) use a flange shape part at the bottom part of the pontoons. The flange is in principle similar to the damping plates used in the offshore industry for SPAR type of structures. The project group initiated the flange part based on the requirement of extra added mass for tuning the bridge system Eigen-modes. Thus, the important modes can be shifted out of the main wave energy zone. The current study will focus on the damping effects of such structure. The damping effects on weak axis bending moment prediction is studied. The modelling of such damping is first proposed according to relevant literature based on both numerical and experimental studies. Since the reference studies were mainly focused on cylindrical structures, it is difficult to obtain an accurate estimation of the damping coefficient for the current bridge pontoon design, which contains a rectangular part between two half-cylindrical parts. In addition, the estimation of pontoon motions needs the input of damping coefficient, which means that the evaluation of damping coefficient is an iteration process. In order to include the uncertainties, a conservative value was adopted to represent the damping effect. The comparison of accounting for the damping effects or not has been given for all the bridge pontoons. The results show that the damping effects are important at the peaks of the responses; in addition, the reduction of the predicted maximum bending moments can be expected around 10–15 percent along different positions of the bridge. However, a further investigation also shows that viscous excitation would increase the bending moments slightly. The comparison also indicates the value of further investigating the effects by CFD or model test methods.
Long floating bridges supported by pontoons with span-widths between 100m and 200m are discrete hydro-elastic structures with many critical eigenmodes. The response of the bridge girder is dominated by vertical eigenmodes and coupled horizontal modes (lateral) and rotational modes (about the longitudinal axis of the bridge girder). In this paper it is focused on design principles to reduce the response with regards to these eigenmodes. It is shown for a floating bridge with 200m span-width that by inserting a bottom flange the vertical eigenmodes can be lifted out of wind driven wave regime. It is also shown that selecting a pontoon length that give cancellation of excitation forces is beneficial, and that the geometrical shaping of the pontoon can be efficient to decrease the bridge response.
Long floating bridges supported by pontoons with span-widths between 100 m and 200 m are discrete hydro-elastic structures with many critical eigenmodes. The response of the bridge girder is dominated by vertical eigenmodes and coupled horizontal modes (lateral) and rotational modes (about the longitudinal axis of the bridge girder). This paper explores the design principles used to reduce the response with regards to these eigenmodes. It is shown for a floating bridge with 200 m span-width that by inserting a bottom flange the vertical eigenmodes can be lifted out of wind-driven wave regime. It is also shown that selecting a pontoon length that leads to cancelation of horizontal excitation forces is beneficial, and that the geometrical shaping of the pontoon can be efficient to decrease the bridge response.
The purpose of this paper is to investigate the main challenges and corresponding solutions for a floating bridge crossing Bjørnafjorden. The paper investigates challenges related to quantification of loads, design of permanent structures as well as temporary phases. The paper evaluates a curved bridge without mooring lines, but considerations are partly valid for a straight bridge anchored to the seabed as well. Both solutions have been used, but the length of the Bjørnafjorden crossing is significantly larger than previous bridges and thus more challenging.
<p>The William R. Bennett Bridge is a new floating bridge across Okanagan Lake in British Columbia, Canada that will replace an existing aging structure. There are several characteristics that make this project unique. The new bridge has floating and fixed sections with complex structural interaction. The floating section has an elevated deck, which was cast while floating and while the pontoon- string assembly was ongoing, thus requiring constant monitoring and ballasting modifications.</p><p>These challenges have been overcome with innovative thinking and close coordination between the design and construction teams that comprise the W. R. Bennett Bridge Group.</p>
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.