Abstract:We report on the high power amplification of 1064nm linearlypolarized laser in all-fiber polarization-maintained MOPA, which can operate at output power level of 1.3kW. The main amplifier was pumped with six 915nm laser diodes, and the slope efficiency is 65.3%. The beam quality (M 2 ) was measured to be <1.2 at full power operation. The polarization extinction rate of the fiber amplifier was measured to be above 94% before mode instabilities (MI) sets in, which reduced to about 90% after the onset of MI. Power scaling capability of strategies for suppressing MI is analyzed based on a novel semi-analytical model, the theoretical results of which agree with the experimental results. It shows that mitigating MI by coiling the gain fiber is an effective and practical way in standard double-cladding large mode area fiber, and, by tight coiling of the gain fiber to the radius of 5.5cm, the MI threshold can be increased to 3 times higher than that without coiling or loose coiling. Experimental study has been carried out to verify the idea, which has proved that MI was suppressed successfully in the amplifier by tight coiling.

In this paper, a spectral model by incorporating SRS effect is proposed and established, which is feasible for analyzing the SRS effect both in high-power fiber oscillator and master oscillator power amplifier (MOPA) system. The theoretical results show that the SRS effect is tightly related to the bandwidths of the fiber Bragg gratings (FBGs) and it can be efficiently suppressed by optimizing the bandwidth of the FBGs. Besides, the established theoretical model is also feasible for analyzing the influence of seed power on the SRS effect. The theoretical predictions agree well with the previous experimental results.

Coherent beam combining of 107 beams has been demonstrated for the first time to the best of our knowledge. When the system was in closed loop, the pattern in far-field was stable and the fringe contrast was > 96 % . The impact of the dynamic tilt error, the piston error, and power inconsistency was theoretically analyzed. Meanwhile, the distribution law of dynamic tilt error was estimated and the correlation of the tilt dithering of different axis was analyzed statistically. The ratio of power in the central lobe was ∼ 22.5 % . The phase residue error in the closed loop was ∼ λ / 22 , which was evaluated by the root-mean-square error of the signal generated from the photoelectric detector.

In this Letter, we demonstrate a kilowatt (kW) level high-power fiber laser amplifier with a clear sign of spectral-broadening-free property. The high-power fiber lasing is realized by employing a master oscillator power-amplifier (MOPA) configuration, seeded by a temporally stable random fiber laser (RFL) that utilizes Raman amplification and random distributed feedback from a long passive fiber. The output power reaches 1.03 kW with a 1070 nm wavelength and an optical-to-optical efficiency of 74.6%. Despite the typical nonlinear spectral broadening in most traditional MOPA systems, the output spectral linewidth is well maintained during the whole high-power amplification process. The suppressed linewidth broadening in the spectral domain during high-power amplification is significant for further power scaling, spectral beam combination, and other applications that require narrow-linewidth high-power lasing.

A fiber laser based on random distributed feedback has attracted increasing attention in recent years, as it has become an important photonic device and has found wide applications in fiber communications or sensing. In this article, recent advances in high-power random distributed feedback fiber laser are reviewed, including the theoretical analyses, experimental approaches, discussion on the practical applications and outlook. It is found that a random distributed feedback fiber laser can not only act as an information photonics device, but also has the feasibility for high-efficiency/high-power generation, which makes it competitive with conventional high-power laser sources. In addition, high-power random distributed feedback fiber laser has been successfully applied for midinfrared lasing, frequency doubling to the visible and high-quality imaging. It is believed that the high-power random distributed feedback fiber laser could become a promising light source with simple and economic configurations.

In this paper, we report a high power single frequency 1030 nm fiber laser with near-diffraction-limited beam quality based on a polarization-maintaining tapered Yb-doped fiber (T-YDF). The T-YDF has advantages of effectively suppressing stimulated Brillouin scattering (SBS) while maintaining good beam quality. As a result, a record output power of 379 W single frequency, linearly polarized, nearly single-mode fiber amplifier operating at 1030 nm is demonstrated. The polarization extinction ratio is as high as 16.3 dB, and the M2 is measured to be 1.12. Further, the dependence of the thermal-induced mode instability (TMI) threshold on the polarization state of an input signal laser is investigated for the first time. By changing the polarization state of the injected seed laser, the output power can increase to 550 W while the beam quality can be maintained well (M2=1.47). The slope efficiency of the whole amplifier is about 80%. No sign of SBS appears even at the highest output power and the further brightness scaling of both situations is limited by the TMI effect. To the best of our knowledge, this result is the highest output power of all-fiberized single frequency fiber amplifiers.

In this paper, an all-fiberized and narrow-linewidth 5 kW power-level fiber amplifier is presented. The laser is achieved based on the master oscillator power amplification (MOPA) configuration, in which the phase-modulated single-frequency laser is applied as the seed laser and bidirectional pumping configuration is applied in the power amplifier. The stimulated Brillouin scattering (SBS), stimulated Raman scattering (SRS), and transverse mode instability (TMI) effects are all effectively suppressed in the experiment. Consequently, the output power is scaled up to 4.92 kW with a slope efficiency of as high as ~ 80%. The 3 dB spectral width is about 0.59 nm, and the beam quality is measured to be M 2 ~ 1.22 at maximum output power. Furthermore, we have also conducted detail spectral analysis on the spectral width of the signal laser, which reveals that the spectral wing broadening phenomenon could lead to the obvious decrease of the spectral purity at certain output power. Overall, this work could provide a well reference for obtaining and optimizing high-power narrow-linewidth fiber lasers.

No abstract