This paper analyses the impact of the method of grinding printed circuit boards (PCBs) in a knife mill on the efficiency and purity of products obtained during electrostatic separation. The separated metals and plastics and ceramics can be used as secondary raw materials. This is in line with the principle of circular economy. Three different screen perforations were used in the mill to obtain different sizes of ground grains. Moreover, the effect of cooling the feed to cryogenic temperature on the final products of separation was investigated. The level of contamination of the concentrate, intermediate, and waste obtained as a result of the application of fixed, determined electrostatic separation parameters was assessed using ICP-AES, SEM–EDS, XRD, and microscopic analysis as well as specific density. The yields of grain classes obtained from grinding in a knife mill were tested through sieve analysis and by using a particle size analyser. The test results indicate that using a knife mill with a 1 mm screen perforation along with cooling the feed to cryogenic temperature significantly improves the efficiency of the process. The grinding products were characterised by the highest release level of the useful substance—metals in the free state. The purity of the concentrate and waste obtained from electrostatic separation was satisfactory, and the content of the intermediate, in which conglomerates of solid metal–plastic connections were present, was very low. The yield of concentrate and waste amounted to 26.2% and 71.0%, respectively. Their purity, reflected in the content of the identified metals (valuable metals), was at the level of 93.3% and 0.5%, respectively. In order to achieve effective recovery of metals from PCBs by means of electrostatic separation, one should strive to obtain a feed composed of grains <1000 μm and, optimally, <800 μm.

In this study, a dual rolls equal channel extrusion (DRECE) process has been applied for improving the mechanical properties of the 5754 alloy. Supplementary experiments involving metallography, electron backscattered diffraction (EBSD), and XRD tests were carried out to evaluate the effect of the DRECE process. XRD analysis showed that the maximum dislocation density was achieved after six DRECE passes, which were accompanied by the formation that is typical for low-strain structures. The increasing dislocation density, as well as grain refinement throughout DRECE deformation, resulted in an increase in the mechanical properties. Annealing of the as-deformed sample resulted in grain growth and strength reduction.

Without the use of appropriate recycling technologies, the growing amount of electronic waste in the world can be a threat to the development of new technologies, and in the case of improper waste management, may have a negative impact on the environment. This is due to the fact that this waste contains large amounts of valuable metals and toxic polymers. Therefore, it should be recycled in accordance with the assumptions of the circular economy. The methods of mechanical recovery of metals from electronic waste, including printed circuits, may be widely used in the future by waste management companies as well as metal production and processing companies. That is why, a well-known and easily applicable electrostatic separation (ES) method was used to recover metals from printed circuit boards. The grain class of 0.32 - 0.10 mm, obtained after grinding the boards, was fed to a separator. Feed and separation products were analyzed by means of ICP-AES, SEM/EDS and XRD. The concentrate yield obtained after electrostatic separation amounted to 32.3% of the feed. Its density was 11.1 g/cc. Out of the 91.44% elements identified in the concentrate, over 90% were metals. XRD, SEM observations and EDS analysis confirmed the presence of non-metallic materials in the concentrate. This relatively high content of impurities indicates the need to grind printed circuit board into grain classes smaller than 0.32-0.10 mm.

The main aim of this research was the preparation of a polymer–ceramic composite with PA-12 as the polymer matrix and modified aluminosilicate cenospheres (CSs) as the ceramic filler. The CSs were subjected to an early purification and cleaning process, which was also taken as a second objective. The CSs were surface modified by a two-step process: (1) etching in Piranha solution and (2) silanization in 3-aminopropyltriethoxysilane. The composite was made for 3D printing by FDM. Raw and modified CSs and a composite with PA-12 were subjected to the following tests: surface development including pores (BET), real density (HP), chemical composition and morphology (SEM/EDS, FTIR), grain analysis (PSD), phase composition (XRD), hardness (HV), and static tensile tests. The composites were subjected to soaking under simulated body fluid (SBF) conditions in artificial saliva for 14, 21, and 29 days. Compared to pure PA-12, PA-12_CS had generally better mechanical properties and was more resistant to SBF at elevated temperatures and soaking times. These results showed this material has potential for use in biomedical applications. These results also showed the necessity of developing a kinetic aging model for aging in different liquids to verify the true value of this material.

The study addressed the microstructure and mechanical properties of hot-rolled advanced high-strength medium manganese steel. Some of the curves that were obtained in static tensile tests at deformation temperatures of 20–200 °C showed the occurrence of the heterogeneous plastic deformation phenomenon, called the Portevin-Le Chatelier (PLC) effect. The deformation temperature significantly influenced a serration character. The correlations between the deformation temperature, serration range, microstructural features, and fracture behavior were investigated. The curves showed no Lüders elongation as a result of the thermomechanical processing applied. The serrated flow phenomenon was observed at 60 and 140 °C. The serration type was different and the most enhanced at 140 °C, where the PLC effect was present in both uniform and post-uniform elongation ranges. The disappearance of serrations at 200 °C was related to the increased diffusion intensity.

The aim of this work was to study the effect of different methods of multi-walled carbon nanotubes (MWCNTs) dispersion, and their influence on the microstructure and properties of aluminium alloy matrix composites produced using the powder metallurgy techniques, such as powder milling/mixing and hot extrusion. The main problem in the manufacturing of nanocomposites is the homogeneous distribution of MWCNTs in the metal matrix. To achieve their proper distribution a high-energy and low-energy mechanical milling, using a planetary ball mill, and mixing, using a turbulent mixer, were applied. Studies have shown that composite materials prepared using milling and extrusion have a much better dispersion of the reinforcing phase, which leads to better mechanical properties of the obtained rods. The low-energy mechanical mixing and mixing using the turbulent mixer neither change the powder morphology nor lead to adequate dispersion of the carbon nanotubes, which directly affects the resulting properties.

This paper evaluates the efficiency of metal recovery from printed circuit boards (PCBs) using two gravity separation devices: a shaking table and a cyclofluid separator. The test results were compared with the results obtained from previous research, where an electrostatic separation process was used for an identically prepared feed. The feed for the separators consisted of PCBs shredded in a knife mill at cryogenic temperatures. The separation efficiency and purity of the products were evaluated based on microscopic analysis, ICP-AES, SEM-EDS, XRD, and specific density. The yield of concentrates (valuable metals) obtained from the shaking table and the cyclofluid separator amounted to 25.7% and 18.9%, respectively. However, the concentrate obtained from the cyclofluid separator was characterised by much higher purity, amounting to ~88% of valuable metals, compared to ~72% for the shaking table. In both cases, middlings formed a significant share, their yield amounting to ~25%, with the share of valuable metals of ~15%. The yield of waste obtained from the shaking table and the cyclofluid separator were 42.6% and 52.5%, respectively. In both cases, as a result of the applied process, the waste was divided into two homogeneous groups differing in grain size and shape. The recovery of metals through gravity separation is possible, in particular, by using a shaking table. These processes can also be applied to separate waste (plastics) into two groups to be selectively processed to produce new materials in line with a circular economy.

In this paper, three commercial cermet powders, WC-Co-Cr, WC-Co and WC-Cr3C2-Ni, were sprayed by the High Velocity Oxy Fuel (HVOF) method onto magnesium alloy AZ31 substrate. The coatings were investigated in terms of their microstructure, phase analysis and residual stress. The manufactured coatings were analyzed extensively using optical microscopy (OM), X-ray diffraction (XRD), scanning (SEM) and transmission electron microscopy (TEM). Based on microstructure studies, it was noted that the coatings show satisfactory homogeneity. XRD analysis shows that in WC-Co, WC-Co-Cr and WC-Cr3C2-Ni coatings, main peaks are related to WC. Weaker peaks such as W2C, Co0.9W0.1, Co and W for WC-Co and W2C, Cr3C2 and Cr7C3 for WC-Cr3C2-Ni also occur. In all cermet coatings, linear stress showed compressive nature. In WC-Co and WC-Cr3C2-Ni, residual stress had a similar value, while in WC-Co-Cr, linear stress was lower. It was also proved that spraying onto magnesium substrate causes shear stress in the WC phase, most likely due to the low elastic modulus of magnesium alloy substrate.