The high-energy requirements of cleanrooms are the main motivation for optimizing their operational conditions. The ventilation system consumes the most energy in order to ensure the precise air conditioning of the room (filtration, temperature, and humidity adjustment). The main function of the ventilation system is to keep particle concentration to a minimum. This work deals with the optimization of an experimental operating room via the optimization of air supply through the distribution element (laminar airflow ceiling) in the range of 0.15–0.25 m·s−1. The laminar airflow between the distribution element and the patient is influenced by the operating light and different airflow velocities. These factors affect changes in particle concentration. Ansys Fluent software was used to investigate the nature of the flow, velocity profiles, and particle trajectories. The results of our numerical simulation demonstrate that a suitable flow rate setting increases the efficiency of particle reduction in the operating table area by up to 54%, which can, in turn, reduce operating costs. The simulated air velocity profile was subsequently verified using the particle image velocimetry (PIV) method. The typical size of particles monitored for in cleanrooms is 0.5 μm according to ISO EN 7. Therefore, the results of this study should be helpful in correctly designing distribution elements for clean rooms.

The assessment of heating systems is not only interested in the efficiency of the heating system itself, but also in the quality of the environment that the heating system creates. The quality of the environment and the heat-humidity microclimate is closely related to thermal comfort. A suitable environment has a positive effect, for example, on the efficiency of work at the workplace. The range of temperatures, humidity and operating temperatures in workplaces is often also legally prescribed in such a way that there is no thermal discomfort for users in the heated space. In terms of savings, it is therefore best to use heating systems that can create a comfortable environment with the lowest possible energy costs. During their development, variations are possible with temperature gradients, the size of the heat exchange area, or the ratio of the radiant and convective components of heat transfer. When developing such systems, it is appropriate to consider CFD simulations. The comparison of the results of CFD simulation and experimental measurement is also in the following article, where the comparison of the operating temperature and the mean radiation temperature of two different heating systems in the model office is monitored.

This paper focuses on the model of gas hydrate formation in an experimental device, which allows the circulation of the resulting mixture (water and gas) and significantly accelerates the process of hydrate formation in the laboratory. A 3D model was developed to better imagine the placement of individual parts of the device. The kinetics of hydrate formation were predicted from equilibrium values of chemical potentials. The aim of solving the equations of state gases in the mathematical model was to optimize the parameters involved in the formation of hydrates. The prediction of the mathematical model was verified by numerical simulation. The mathematical model and numerical simulation predict the chemical reaction evolving over time and determine the amount of crystallized water in the reactor. A remarkable finding is that the deviation of the model and simulation at the initiation the calculation of crystallized water starts at 76% and decreases over time to 2%. Subsequently, the number of moles of bound gas in the hydrate acquires the same percentage deviations. The amount of water supplied to the reactor is expressed by both methods identically with a maximum deviation of 0.10%. The different character is shown by the number of moles of gas remaining in the reactor. At the beginning of the calculation, the deviation of both methods is 0%, but over time the deviation slowly increases, and at the end it expresses the number of moles in the reactor with a deviation of 0.14%. By previous detection, we can confirm that the model successfully determines the amount of methane hydrate formed in the reactor of the experimental equipment. With the attached pictures from the realized experiment, we confirmed that the proposed method of hydrate production is tested and takes minutes. The article calculates the energy efficiency of natural gas hydrate in the proposed experimental device.

The trend of constantly increasing energy prices can be observed especially in the increased demands on the thermal insulation properties of building structures. The possibilities of reducing the energy intensity of residential buildings also include the right choice of technology for heating, cooling and hot water preparation. Different cooling systems have different proportions of convection and radiant components. This results in a variety of temperature profiles, and thus also directly affect the quality of the environment in terms of thermal comfort. For efficient heating, it is therefore best to choose a cooling system with a minimum temperature gradient in both the horizontal and vertical directions. At the same time, however, the investment costs for the cooling system must be considered. From this point of view, it seems to be most advantageous to use one system for both heating and cooling. From the point of view of comfort, the most suitable choice of cooling system is ceiling cooling. On the contrary, this system is less suitable for heating compared to the floor system. Therefore, if you are considering the design of a system that will be the greater part of the operation for heating the building and during the summer months will be used to increase thermal comfort by cooling in buildings with lower heat loads [1].

Various waste materials have energy potential. It is important to make use of this potential and prepare the product for further use by treating the waste. Treatments such as compressing waste into pellets leads to increasing the energy density of this fuel, which benefits transport and storage costs. However, low bulk density, high ash content, low-ash melting temperatures, and low calorific values of non-woody pellets can cause problems during their combustion. This article deals with the energy usage of walnut shells, which were blended with spruce sawdust in various amounts and compressed into pellets. The mechanical and energy properties of these were measured and compared with recommended or standardized values. The formed pellets met the quality limit for bulk density, ash content, moisture content, the content of nitrogen and sulfur, and net calorific value according to ISO 17225. However, low ash melting temperatures were noticed for pellets from pure walnut shells, and also lower mechanical durability for produced pellets with walnut shells contents higher than 10% were detected.

No abstract

For countries with limited access to conventional hydrocarbon gases, methane hydrates appear as a possible source of energy or as a strategic concern for the creation of alternative natural gas reserves. Currently, natural gas hydrates are beginning to be included in the considerations of gas supply for the next decades. From a perspective point of view, the accumulation of natural gas in the form of hydrate structures and subsequent release, if necessary, proves to be very advantageous. Storing gas in such a form creates an energy-efficient interest in developing and innovating technology in this area.

No abstract