Several natural materials and vegetable waste have relevant mechanical properties, mainly in its fiber format. Particularly, banana fiber (BF) provides a close behavior to the widely spread glass fibers, which places it in an advantageous position for use as a reinforcing material in plastic composites. This work characterizes the behavior of acrylonitrile butadiene styrene (ABS), high impact polystyrene (HIPS), and high density polyethylene (HDPE) reinforced with short fibers of bananas from the Canary Islands for its application in molding processes. Several thermal analyses (Thermal Gravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), and Melt Flow Index (MFI)) and mechanical tests (tensile, flexural, impact, and Dynamic Mechanical Analysis (DMA)) were carried out in composites with different percentages of banana fiber. The thermal results show that the use of banana fiber is viable as a reinforcement in composites for injection molding processes and the mechanical tests indicate an increase in stiffness and an improvement in maximum flexural stress by increasing the fiber content in composites, so the banana fiber turns out to be a natural alternative for the reinforcement of injected plastic components.

Bags used to protect and accelerate the ripening of bananas are a clear example of the environmental problem of packaging waste. Small pieces of these non-biodegradable bags are frequently disposed on the soil by accident (environmental conditions and poor handling during the harvest) and remain there for years. This work focuses on the development of protective biodegradable bags reinforced with banana fiber, obtained from waste of the banana plants, thus promoting a circular economy and a more environmentally friendly process. To achieve this, different bio-based composites were tested (processability) by compounding extrusion (biopolymer and banana fiber with different process steps) and blown film extrusion. The bags produced were tested in field and sequentially improved in three generations of biofilms. The results showed that the maximum processable fiber content was 5 wt %. Additionally, the micronizing of the compounds was crucial to simplify the blown film extrusion and improve the smoothness of the bags (scratches avoidance on the banana surface). The final bags (Mater-Bi biopolymer, 5% combed and sieved banana fiber, and 2.5 wt % TiO2 for ultraviolet light filtration), performed better than the conventional ones (faster maturing, i.e., earlier harvest, and easier handling) and fulfilled the biodegradability, composting and ecotoxicity test requirements.

The article is focused on analysis of global efficiency of new mold for rotational molding of plastic parts, being directly heated by thermal fluid. The overall efficiency is based on several items such as reduction of cycle time, better uniformity of heating-cooling and low energy consumption. The new tool takes advantage of additive fabrication and electroforming for making the optimal manifold and cavity shell of the mold. Experimental test of a prototype mold was carried out on an experimental rotational molding machine, developed for this purpose, measuring wall temperature, and internal air temperature, with and without plastic material inside. Results were compared with conventional mold heated into an oven and to theoretical simulations done by Computational Fluid Dynamic software (CFD). The analysis represents considerable improvement of cycle time related to conventional methods (heated by oven) and better thermal uniformity to conventional procedures by direct heating of oil with external channels. In addition to thermal analysis an energetic efficiency study was done. POLYM. ENG.

Atomic Diffusion Additive Manufacturing (ADAM) is an innovative Additive Manufacturing process that allows the manufacture of complex parts in metallic material, such as copper among others, which provides new opportunities in Rapid Tooling. This work presents the development of a copper electrode manufactured with ADAM technology for Electrical Discharge Machining (EDM) and its performance compared to a conventional electrolytic copper. Density, electrical conductivity and energy-dispersive X-ray spectroscopy were performed for an initial analysis of both ADAM and electrolytic electrodes. Previously designed EDM experiments and optimizations using genetic algorithms were carried out to establish a comparative framework for both electrodes. Subsequently, the final EDM tests were carried out to evaluate the electrode wear rate, the roughness of the workpiece and the rate of material removal for both electrodes. The EDM results show that ADAM technology enables the manufacturing of functional EDM electrodes with similar material removal rates and rough workpiece finishes to conventional electrodes, but with greater electrode wear, mainly due to internal porosity, voids and other defects observed with field emission scanning electron microscopy.

No abstract