Soldering with the lead-free tin-base alloys requires substantially higher temperatures (;235-250°C) than those (213-223°C) required for the current tin-lead solders, and the rates for intermetallic compound (IMC) growth and substrate dissolution are known to be significantly greater for these alloys. In this study, the IMC growth kinetics for Sn-3.7Ag, Sn-0.7Cu, and Sn-3.8Ag-0.7Cu solders on Cu substrates and for Sn-3.8Ag-0.7Cu solder with three different substrates (Cu, Ni, and Fe-42Ni) are investigated. For all three solders on Cu, a thick scalloped layer of h phase (Cu 6 Sn 5 ) and a thin layer of e phase (Cu 3 Sn) were observed to form, with the growth of the layers being fastest for the Sn-3.8Ag-0.7Cu alloy and slowest for the Sn-3.7Ag alloy. For the Sn-3.8Ag-0.7Cu solder on Ni, only a relatively uniform thick layer of h phase (Cu,Ni) 6 Sn 5 growing faster than that on the Cu substrate was found to form. IMC growth in both cases appears to be controlled by grain-boundary diffusion through the IMC layer. For the Fe-42Ni substrate with the Sn-3.8Ag-0.7Cu, only a very thin layer of (Fe,Ni)Sn 2 was observed to develop.

The wetting of a molten solder on metallic surfaces is a rather complex phenomenon. In addition to physical spreading due to surface tension reduction, there are interfacial metallurgical and flux chemical reactions with the metallic substrate surface. Substrate dissolution and intermetallic formation take place rapidly during soldering. Since lead-free soldering requires substantially higher soldering temperatures (around 250 C), the rates of intermetallic growth and substrate dissolution for lead-free solders are expected to be significantly greater than those for the current Sn-Pb eutectic solder. This study systematically investigates the metallurgy of the solid-liquid interface reactions and intermetallic growth kinetics for three lead-free solders: Sn-Ag eutectic (96.5%Sn-3.5%Ag), Sn-Cu eutectic (99.3%Sn-0.7%Cu) and Sn-AgCu eutectic (Sn-3.8Ag-0.7Cu, SAC 387) with three metallic substrates: Cu, Ni, and Alloy 42 (42%Ni-52%Fe) over temperatures ranging from 225 to 280 C for reaction time from 10 s to 16 h. Wetting behavior of these three alloys on PCBs with OSP, immersion Sn, and Ni/Au finishes, was also examined from 220 C up to 260 C. A thorough understanding of lead-free solder/substrate interfacial reactions should give guidance to the optimum lead-free soldering processes and to the optimum lead-free coating thicknesses for component and PCB terminal finishes, as well as for under-chip metallurgical coatings for flip-chip and BGA applications.

PurposeTo investigate effects of the thermal history on intermetallic thickness and morphology and on the resulting shear strength of the ball attachment for a variety of BGA components.Design/methodology/approachIn this study, a variety of BGA components with balls made of Pb‐free Sn‐Ag‐Cu (SAC) 305, Sn‐Pb eutectic and high‐temperature 90Pb‐10Sn alloys, were subjected to different thermal histories, including up to ten reflow cycles, and aged at 125°C from 24 to 336 h. The intermetallic thickness and morphology after these thermal events were then examined under optical and scanning electronic microscopes. Ball shearing tests were conducted to investigate effects of the thermal history and intermetallic thickness and morphology on shearing strength of these solder balls.FindingsThe results show that effects directly from intermetallic layers may or may not be detectable; and the shear strength of solder balls is largely dependent on the solder alloy and its microstructure. Shear strength increases are observed after multiple reflow cycles and ageing at elevated temperature for the two Pb‐bearing alloys, while the SAC305 lead‐free alloy shows slight reductions in both strength and ductility after thermal exposure.Practical implicationsPresented results can be used for estimation of reliability for electronic assemblies subjected to multiple rework and repair operations, which expose sensitive components, such as BGAs, to elevated temperatures.Originality/valueIt is believed that a sound understanding of the effects of intermetallic morphology and thickness on reliability of BGA solder balls can lead to more intelligent choice of soldering processes, as well as to rework/repair process optimisation and to establishing their operational limits.

Fundamental study of deformation and fatigue fracture behavior of solder alloys under complex load conditions is a key to enabling implementation of sophisticated three-dimensional (3D) time-dependent nonlinear finite-element stress and strain analyses for the life assessment for electronic packages and assemblies. In this study, the rate-dependent deformation and fatigue fracture behavior of Sn3.8Ag0.7CuPb-free alloy and Sn–Pb eutectic alloy was investigated with thin-walled specimens using a biaxial servo-controlled tension–torsion material testing system, with solder alloys subjected to a variety of complex load conditions: pure shearing at strain rates between 6.7×10−7∕s and 1.3×10−1∕s, creep at temperatures ranging from room temperature up to 125°C, and cyclic loading with frequencies of 0.001Hz to 3Hz. Biaxial stress conditions were imposed to investigate the effects of multiaxial stresses on deformation behavior. The effects of frequency and temperature on cyclic deformation and fatigue facture were investigated for lead-free Sn3.8Ag0.7Cu and Sn–Pb eutectic solder. Fractography of fatigue tested samples was also conducted to determine possible fatigue failure mechanisms.

Fundamental study of deformation and fatigue fracture behavior of solder alloys under complex load conditions is a key to enabling implementation of sophisticated 3-D time-dependent nonlinear FEM stress and strain analyses and life assessment for electronic packages and assemblies. In this study, the rate-dependent deformation and fatigue fracture behavior of Sn3.8Ag0.7Cu Pb-free alloy and Sn-Pb eutectic alloy was investigated with thin-walled specimens using a bi-axial servo-controlled tension-torsion material testing system, with solder alloys subjected to a variety of complex load conditions: pure shearing at strain rates between 6.7×10−7 /sec to 1.3×10−1 /sec, creep at temperatures ranging from room temperature up to 125 °C, and cyclic loading with frequency of 0.001Hz to 3Hz. Bi-axial stress conditions were imposed for shearing tests to investigate effects of multi-axial stresses on deformation behavior. The effects of frequency and temperature on cyclic deformation and fatigue facture were investigated for lead-free Sn3.8Ag0.7Cu and Sn-Pb eutectic solder. Fractography of fatigue tested samples were also conducted to determine possible fatigue failure mechanisms.