Hydrogels, due to their unique biocompatibility, flexible methods of synthesis, range of constituents, and desirable physical characteristics, have been the material of choice for many applications in regenerative medicine. They can serve as scaffolds that provide structural integrity to tissue constructs, control drug and protein delivery to tissues and cultures, and serve as adhesives or barriers between tissue and material surfaces. In this work, the properties of hydrogels that are important for tissue engineering applications and the inherent material design constraints and challenges are discussed. Recent research involving several different hydrogels polymerized from a variety of synthetic and natural monomers using typical and novel synthetic methods are highlighted. Finally, special attention is given to the microfabrication techniques that are currently resulting in important advances in the field.

Although researchers currently have limited ability to mimic the natural stem cell microenvironment, recent work at the interface of stem biology and biomaterials science has demonstrated that control over stem cell behavior with artificial microenvironments is quite advanced. Embryonic and adult stem cells are potentially useful platforms for tissue regeneration, cell-based therapeutics, and disease-in-a-dish models for drug screening. The major challenge in this field is to reliably control stem cell behavior outside the body. Common biological control schemes often ignore physicochemical parameters that materials scientists and engineers commonly manipulate, such as substrate topography and mechanical and rheological properties. However, with appropriate attention to these parameters, researchers have designed novel synthetic microenvironments to control stem cell behavior in rather unnatural ways. In this Account, we review synthetic microenvironments that aim to overcome the limitations of natural niches rather than to mimic them. A biomimetic stem cell control strategy is often limited by an incomplete understanding of the complex signaling pathways that drive stem cell behavior from early embryogenesis to late adulthood. The stem cell extracellular environment presents a miscellany of competing biological signals that keep the cell in a state of unstable equilibrium. Using synthetic polymers, researchers have designed synthetic microenvironments with an uncluttered array of cell signals, both specific and nonspecific, that are motivated by rather than modeled after biology. These have proven useful in maintaining cell potency, studying asymmetric cell division, and controlling cellular differentiation. We discuss recent research that highlights important biomaterials properties for controlling stem cell behavior, as well as advanced processes for selecting those materials, such as combinatorial and high-throughput screening. Much of this work has utilized micro- and nanoscale fabrication tools for controlling material properties and generating diversity in both two and three dimensions. Because of their ease of synthesis and similarity to biological soft matter, hydrogels have become a biomaterial of choice for generating 3D microenvironments. In presenting these efforts within the framework of synthetic biology, we anticipate that future researchers may exploit synthetic polymers to create microenvironments that control stem cell behavior in clinically relevant ways.

Object. Spinal cord injury (SCI) is a complex pathological entity, the treatment of which requires a multipronged approach. One way to integrate different therapeutic strategies for SCI is to develop implantable scaffolds that can deliver therapies in a synergistic manner. Many investigators have developed implantable “bridges,” but an important property of such scaffolds—that is, mechanical compatibility with host tissues—has been neglected. In this study, the authors evaluated the results of implanting a mechanically matched hydrogel-based scaffold to treat SCI. Methods. A nonbiodegradable hydrogel, poly(2-hydroxyethylmethacrylate) (PHEMA), was engineered using thermally initiated free radical solution polymerization. Two groups of 12 adult Sprague—Dawley rats underwent partial cervical hemisection injury followed by implantation of either PHEMA or PHEMA soaked in 1 µg of brain-derived neurotrophic factor (BDNF). Four rats from each group were killed 1, 2, or 4 weeks after induction of the injury. Immunofluorescence staining was performed to determine the presence of scarring, cellular inflammatory responses, gliosis, angiogenesis, and axonal growth in and around the implanted scaffolds. Conclusions. The implanted PHEMA with 85% water content had a compressive modulus of 3 to 4 kPa, which matched the spinal cord. Implanted PHEMA elicited modest cellular inflammatory responses that disappeared by 4 weeks and minimal scarring was noted around the matrix. Considerable angiogenesis was observed in PHEMA, and PHEMA soaked in BDNF promoted axonal penetration into the gel. The authors conclude that mechanically engineered PHEMA is well accepted by host tissues and might be used as a platform for sustained drug delivery to promote axonal growth and functional recovery after SCI.

Micro-/nanoscale technologies such as lithographic techniques and microfluidics offer promising avenues to revolutionalize the fields of tissue engineering, drug discovery, diagnostics and personalized medicine. Microfabrication techniques are being explored for drug delivery applications due to their ability to combine several features such as precise shape and size into a single drug delivery vehicle. They also offer to create unique asymmetrical features incorporated into single or multiple reservoir systems maximizing contact area with the intestinal lining. Combined with intelligent materials, such microfabricated platforms can be designed to be bioadhesive and stimuli-responsive. Apart from drug delivery devices, microfabrication technologies offer exciting opportunities to create biomimetic gastrointestinal tract models incorporating physiological cell types, flow patterns and brush-border like structures. Here we review the recent developments in this field with a focus on the applications of microfabrication in the development of oral drug delivery devices and biomimetic gastrointestinal tract models that can be used to evaluate the drug delivery efficacy.

A novel method for synthesizing nanoscale polymer networks that swell in acidic media is described here using photoinitiated emulsion polymerization. These nanomatrices consist of a crosslinked core of poly[2-(diethylamino)ethyl methacrylate] surface grafted with poly(ethylene glycol) (PDGP) with an average diameter of 50-150 nm. Control over mesh size, surface charge, encapsulation efficiency and in vitro biocompatibility was obtained by varying crosslinking density. The ability to image nanomatrices in their dry state using conventional scanning electron microscopy was made possible by increasing crosslinking density. Theoretical calculations of matrix mesh sizes were supported by the encapsulation of both insulin and colloidal gold 2-5 nm in diameter. The ability to sequester and control the aggregation of an inorganic phase confirmed their use as a nanocomposite matrix material. These networks could be used as imaging agents, drug delivery devices or as components of sensing devices.