This paper describes a new research facility which experimentally models hot gas ingestion into the wheel-space of an axial turbine stage. Measurements of CO2 gas concentration in the rim-seal region and inside the cavity are used to assess the performance of two generic (though engine-representative) rim-seal geometries in terms of the variation of concentration effectiveness with sealing flow rate. The variation of pressure in the turbine annulus, which governs this externally-induced (EI) ingestion, was obtained from steady pressure measurements downstream of the vanes and near the rim seal upstream of the rotating blades. Although the ingestion through the rim seal is a consequence of an unsteady, three-dimensional flow field and the cause-effect relationship between pressure and the sealing effectiveness is complex, the experimental data is shown to be successfully calculated by simple effectiveness equations developed from a previously published orifice model. The data illustrate that, for similar turbine-stage velocity triangles, the effectiveness can be correlated using a non-dimensional sealing parameter, Φo. In principle, and within the limits of dimensional similitude, these correlations should apply to a geometrically-similar engine at the same operating conditions. Part 2 of this paper describes an experimental investigation of rotationally-induced (RI) ingress, where there is no mainsteam flow and consequently no circumferential variation of external pressure.

This paper describes a new research facility which experimentally models hot gas ingestion into the wheel-space of an axial turbine stage. Measurements of the CO2 gas concentration in the rim-seal region and inside the cavity are used to assess the performance of two generic (though engine-representative) rim-seal geometries in terms of the variation of concentration effectiveness with sealing flow rate. The variation of pressure in the turbine annulus, which governs this externally-induced (EI) ingestion, was obtained from steady pressure measurements downstream of the vanes and near the rim seal upstream of the rotating blades. Although the ingestion through the rim seal is a consequence of an unsteady, three-dimensional flow field and the cause-effect relationship between the pressure and the sealing effectiveness is complex, the experimental data is shown to be successfully calculated by simple effectiveness equations developed from a previously published orifice model. The data illustrate that, for similar turbine-stage velocity triangles, the effectiveness can be correlated using a nondimensional sealing parameter, Φo. In principle, and within the limits of dimensional similitude, these correlations should apply to a geometrically-similar engine at the same operating conditions. Part II of this paper describes an experimental investigation of rotationally-induced (RI) ingress, where there is no mainstream flow and consequently no circumferential variation of external pressure.

The flow inside cavities between co-rotating compressor discs of aero-engines is driven by buoyancy, with Grashof numbers exceeding 10 13 . This phenomenon creates a conjugate problem: the Nusselt numbers depend on the radial temperature distribution of the discs, and the disc temperatures depend on the Nusselt numbers. Furthermore, Coriolis forces in the rotating fluid generate cyclonic and anti-cyclonic circulations inside the cavity. Such flows are three-dimensional, unsteady and unstable, and it is a challenge to compute and measure the heat transfer from the discs to the axial throughflow in the compressor. In this paper, Nusselt numbers are experimentally determined from measurements of steady-state temperatures on the surfaces of both discs in a rotating cavity of the Bath Compressor-Cavity Rig. The data are collected over a range of engine-representative parameters and are the first results from a new experimental facility specifically designed to investigate buoyancy-induced flow. The radial distributions of disc temperature were collected under carefully-controlled thermal boundary conditions appropriate for analysis using a Bayesian model combined with the equations for a circular fin. The Owen-Tang buoyancy model has been used to compare predicted radial distributions of disc temperatures and Nusselt numbers with some of the experimentally determined values, taking account of radiation between the interior surfaces of the cavity.The experiments show that the average Nusselt numbers on the disc increase as the buoyancy forces increase. At high rotational speeds the temperature rise in the core, created by compressibility effects in the air, attenuates the heat transfer and there is a critical rotational Reynolds number for which the Nusselt number is a maximum. In the cavity, there is an inner region dominated by forced convection and an outer region dominated by buoyancy-induced flow. The inner region is a mixing region, in which entrained cold throughflow encounters hot flow from the Ekman layers on the discs. Consequently, the Nusselt numbers on the downstream disc in the inner region tend to be higher than those on the upstream disc.

This paper describes experimental results from a research facility which experimentally models hot gas ingress into the wheel-space of an axial turbine stage. Measurements of CO2 gas concentration in the rim-seal region and inside the wheel-space are used to assess the performance of generic (though engine-representative) single and double seals in terms of the variation of concentration effectiveness with sealing flow rate. The variation of pressure in the turbine annulus, which governs externally-induced ingress, was obtained from steady pressure measurements downstream of the vanes. The benefit of using double seals is demonstrated: the ingested gas is shown to be predominately confined to the outer wheel-space radially outward of the inner seal; in the inner wheel-space, radially inward of the inner seal, the effectiveness is shown to be significantly higher. Criteria for ranking the performance of single and double seals are proposed, and the performance limit for any double seal is shown to be one in which the inner seal is exposed to rotationally-induced ingress. Although the ingress is a consequence of an unsteady, three-dimensional flow field and the cause-effect relationship between pressure and the sealing effectiveness is complex, the experimental data is shown to be successfully calculated by simple effectiveness equations developed from a theoretical model. The data illustrate that, for similar turbine-stage velocity triangles, the effectiveness can be correlated using two empirical parameters. In principle, these correlations could be extrapolated to a geometrically-similar turbine operating at engine-representative conditions.

Rotationally-induced (RI) ingress is caused by the negative pressure (relative to the external air) inside the wheel-space of a gas turbine; this negative pressure, which is created by the rotating flow in the wheel-space, drives the ingestion of hot gas through the rim seals. Externally-induced (EI) ingress is caused by the circumferential distribution of pressure created by the blades and vanes in the turbine annulus: ingress occurs in those regions where the external pressure is higher than that in the wheel-space, and egress occurs where it is lower. Although EI ingress is the dominant mechanism for hotgas ingestion in engines, there are some conditions in which RI ingress has an influence: this is referred to as combined ingress (CI). In Part 1 of this two-part paper, values of the sealing effectiveness (obtained using the incompressible orifice equations developed for EI ingress in an earlier paper) are compared with published experimental data and with results obtained using 3D steady compressible CFD (Computational Fluid Dynamics). Acceptable limits of the incompressible-flow assumption are quantified for the orifice model; for the CFD, even though the Mach number in the annulus reaches approximately 0.65, it is shown that the incompressible orifice equations are still valid. The results confirm that EI ingress is caused predominantly by the magnitude of the peak-to-trough circumferential difference of pressure in the annulus; the shape of the pressure distribution is of secondary importance for the prediction of ingress. A simple equation, derived from the orifice model, provides a very good correlation of the computed values of effectiveness. Using this correlation, it is possible to estimate the minimum sealing flow rate to prevent ingress without the need to know anything about the pressure distribution in the annulus; this makes the orifice model a powerful tool for rim-seal design.

The flow inside cavities between co-rotating compressor discs of aero-engines is driven by buoyancy, with Grashof numbers exceeding 1013. This phenomenon creates a conjugate problem: the Nusselt numbers depend on the radial temperature distribution of the discs, and the disc temperatures depend on the Nusselt numbers. Furthermore, Coriolis forces in the rotating fluid generate cyclonic and anti-cyclonic circulations inside the cavity. Such flows are three-dimensional, unsteady and unstable, and it is a challenge to compute and measure the heat transfer from the discs to the axial throughflow in the compressor. In this paper, Nusselt numbers are experimentally determined from measurements of steady-state temperatures on the surfaces of both discs in a rotating cavity of the Bath Compressor-Cavity Rig. The data are collected over a range of engine-representative parameters and are the first results from a new experimental facility specifically designed to investigate buoyancy-induced flow. The radial distributions of disc temperature were collected under carefully-controlled thermal boundary conditions appropriate for analysis using a Bayesian model combined with the equations for a circular fin. The Owen-Tang buoyancy model has been used to compare predicted radial distributions of disc temperatures and Nusselt numbers with some of the experimentally determined values, taking account of radiation between the interior surfaces of the cavity. The experiments show that the average Nusselt numbers on the disc increase as the buoyancy forces increase. At high rotational speeds the temperature rise in the core, created by compressibility effects in

The change in compressor blade-tip clearance across the flight cycle depends on the expansion of the rotor, which in turn depends on the temperature and stress in the discs. The radial distribution of temperature is directly coupled to the buoyancy-driven flow and heat transfer in the rotating disc cavities. This paper describes a new test rig specifically designed to investigate this conjugate phenomenon. The rig test section includes four rotating discs enclosing three cavities. Two discs in the central cavity are instrumented with thermocouples to provide the radial distribution of temperature; the two outer cavities are thermally insulated to create appropriate boundary conditions for the heat transfer analysis. An axial throughflow of air is supplied between a stationary shaft and the bore of the discs. The temperature of the throughflow air is measured by thermocouples in rakes upstream and downstream of the central cavity. For a cold throughflow, the outer shroud of the central cavity is heated. Two independently-controlled radiant heaters allow differential shroud temperatures for the upstream and downstream discs, as found in aero-engine compressors. Alternatively, the throughflow can be heated above the shroud temperature to simulate the transient conditions during engine operation where stratified flow can occur inside the cavity. The rig is designed to operate in conditions where both convective and radiative heat transfer dominate; all internal surfaces of the cavity are painted matt black to allow the accurate calculation of the radiant heat transfer.

Part 1 of this two-part paper presented experimental results for externally-induced (EI) ingress, where the ingestion of hot gas through the rim seal into the wheel-space of a gas turbine is controlled by the circumferential variation of pressure in the external annulus. In Part 2, experimental results are presented for rotationally-induced (RI) ingress, where the ingestion is controlled by the pressure generated by the rotating fluid in the wheel-space. Although EI ingress is the common form of ingestion through turbine rim seals, RI ingress or combined ingress (where EI and RI ingress are both significant) is particularly important for double seals, where the pressure asymmetries are attenuated in the annular space between the inner and outer seals. In this paper, the sealing effectiveness was determined from concentration measurements, and the variation of effectiveness with sealing flow rate was compared with theoretical curves for RI ingress obtained from an orifice model. Using a nondimensional sealing parameter, Φ0, the data could be collapsed onto a single curve, and the theoretical variation of effectiveness with Φ0 was in very good agreement with the data for a wide range of flow rates and rotational speeds. It was shown that the sealing flow required to prevent RI ingress was much less than that needed for EI ingress, and it was also shown that the effectiveness of a radial-clearance seal is significantly better than that for an axial-clearance seal for both EI and RI ingress.