A significant factor, which leads to the discrepancy of the final sizes of the bent sheet parts to their drawings is the springing of the sheet blank during bending. At the same time, the springing during multi-pass bending is not sufficiently studied. The purpose of the work is to obtain the graphical and mathematical dependencies for descriptions of the resultative spring-back angle of the blanks at the multi-pass bending, taking into account the width of the blank, number of passes, and pre-bending angle at each preliminary pass. The paper describes the basic information about the difference between the spring-back angle for one-pass or multi-pass bending. In the course of the study it is shown that during calculations of forming and preventive prediction of the geometric quality of bending shapes it is necessary to take into account properties of the blank material, as well as the angles of the prebends and the width to thickness ratio of the blank. A methodology of experimental research was developed for determining the spring-back angle during multi-pass bending in three bending dies with 109°, 91° and 72° pass-by-pass reducing angles.
Приазовский государственный технический университет Кухарь В.В. Приазовский государственный технический университет Ткачев Р.О. Приазовский государственный технический университет Радушев О.О. Приазовский государственный технический университет ЭКСПЕРИМЕНТАЛЬНОЕ ИССЛЕДОВАНИЕ ЖЕСТКОСТИ ГНУТЫХ И ГНУТО-СВАРНЫХ АРМИРУЮЩИХ ПРОФИЛЕЙ ОДНОГО ТИПОРАЗМЕРА ПРИ ИСПЫТАНИЯХ НА ПОПЕРЕЧНЫЙ ИЗГИБ У статті наведені результати випробувань на поперечний вигин армуючих профілів однакового типорозміру двох варіантів виготовлення. Були проведені випробування зразків із профілів, виготовлених за технологією багатовалкового гнуття профілю замкнутого перетину з наявністю зазору на стороні 50 мм і за технологією з формуванням поздовжнього зварного шва після гнуття на стороні 40 мм. Удосконалено методику експериментальних досліджень холодногнутих профілів на поперечний вигин прикладеною силою із безперервним відеозаписом процесу.Виконано статистичну обробку результатів вимірювань товщини стінок, наданих для випробувань армуючих профілів. Отримано графічні та аналітичні залежності величини прогину профілю за варіантами навантаження на більшу і меншу стінки від величини навантаження. З аналізу графічних залежностей виявлено, що, незважаючи на меншу, на 4,8% товщину армуючого профілю ПГЗ порівняно з профілем ПГ, величина прогину для найбільш несприятливого випадку навантаження (на більшу сторону) зменшується на 59%, а при навантаженні на меншу сторону прогин знижується на 0,7%.Після обробки експериментальних результатів отримано степенні рівняння регресії для різних умов навантаження зразків на більшу і меншу стінки. Встановлено, що виготовлення армуючих профілів у гнуто-звареному виконанні має переваги за показниками жорсткості перед профілями, виготовленими в гнутому виконанні. Для найбільш несприятливого варіанта навантаження профілю на більшу сторону, коли незварений проміжок знаходиться на його боці, варіант формування зварного шва дає поліпшення показника жорсткості не менше ніж на 50%.Ключові слова: гнуття, багатоперехідне гнуття, профіль, армуючий профіль, випробування, зварювання, зварений шов, триточковий вигин.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.