Bu çalışmada, demir esaslı malzemelerden sonra en önemli metal grubunu oluşturan alüminyum alaşımlarının oda sıcaklığında deformasyon hızı ve haddeleme yönüne bağlı olarak çekme testi davranışları incelenmiştir. Alüminyum alaşımlarından ısıl işlem uygulanabilir gruptan AA6082-T6 alaşımı, ısıl işlem uygulanamaz gruptan AA1035-H14 alaşımı seçilmiştir. Haddeleme yönünün çekme ekseniyle yaptığı açılar 0°, 45° ve 90°, deformasyon hızları 2.4x10-4 , 2.4x10-3 , 2.4x10-2 ve 1.2x10-1 s-1 olarak belirlenmiştir. 2.4x10-4 s-1 deformasyon hızında AA1035-H14 alaşımında 45° ve 90° hadde yönünde çekme mukavemeti düşük kalmıştır. Her iki alaşımda da en yüksek çekme dayanımı değeri 0° hadde yönünde elde edilmiştir. Ancak, AA6082-T6 alaşımında en düşük çekme mukavemeti 90° hadde yönünde iken, AA1035-H14 alaşımında en düşük çekme mukavemeti 45° hadde yönündedir. Diğer taraftan, AA6082-T6 alaşımında 90° hadde yönünde nispeten daha yüksek akma dayanımı değeri elde edilmişken, AA1035-H14 alaşımında akma dayanımı 0° hadde yönünde daha yüksek değer almıştır. 2.4 x 10-4 s-1 deformasyon hızında, AA1035-H14 alüminyum alaşımında hadde yönünün mukavemet üzerindeki etkisi daha belirgin olmuştur. Kopma uzaması her iki alaşımda da 90° hadde yönünde önemli ölçüde düşük kalmıştır. Her iki alaşımda da, genel olarak deformasyon hızı artışıyla mukavemet değerleri artmıştır. Bu artış her iki alaşımda da, çekme mukavemetinde nispeten sınırlı kalırken akma mukavemetinde daha belirgindir. Ayrıca, AA1035-H14 alaşımı ile karşılaştırıldığında AA6082-T6 alaşımında deformasyon hızının mukavemet üzerindeki etkisi daha dikkat çekicidir. Kopma uzaması AA6082-T6 alaşımında genel olarak yüksek deformasyon hızında düşük kalırken, AA1035-H14 alaşımında ise genel olarak deformasyon hızı artışıyla kopma uzaması değerleri artmaktadır. Ancak, AA1035-H14 alaşımında, 45° ve 90° hadde yönünde 1.2x10-1 s-1 deformasyon hızında kopma uzamasında belirgin olarak düşüş de meydana gelmektedir.
Self-piercing riveting (SPR) is a high-speed mechanical joining technique for sheet metal materials. In this study, the mechanical properties of DC04 steel and AA5182 aluminium alloy in triple combinations joined by the SPR method were investigated. For this purpose, triple-joining processes were performed in different combinations, and macro-structural analysis and tensile shear tests were carried out by comparing their mechanical properties. As a result of the study, the highest shear forces were obtained in FFA (DC04-DC04-AA5182) and AFF (AA5182-DC04-DC04) combinations. As the number of aluminium layers increases, the probability of tearing increases in triple joining. Higher spread ratios were generally measured under conditions with hard materials in the upper layers and soft materials in the lower layers.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.