Recently, carbon nanostructures are of high importance due to their unique characteristics and interesting applications. Pyrolysis of anthracene with cobalt complex Co(2,2′-bipy)Cl2(1), where (2,2′-bipy) is 2,2′-bipyridine, in the absence and presence of silica gave in high yield cobalt-carbon nanocomposite CoCNC (2) and CoCNC@SiO2(3) at 600 °C and 850 °C, respectively. They were characterized using SEM, TEM, PXRD, Raman and XPS. (3) and (2) contain core–shell cobalt(0)/cobalt oxide-graphite with or without silica support. PXRD indicates that (2) contains crystalline hexagonal α-Co and cubic β-Co phases while (3) contains only cubic β-Co phase and silica. The structure of (2) is 3D hierarchical carbon architecture wrapping spherical and elliptical cobalt nanoparticles. (3) consists of graphitized structures around cobalt nanoparticles embedded in the silica matrix. XPS reveals that the nanocomposites contain oxygen functional groups that enhance uptake of cationic dyes. CoCNC@SiO2(3) has higher capacity and thus is better adsorbent of Basic Violet 3 than CoCNC (2). The Langmuir adsorption capacity of (3) is 19.4 mg g−1 while column capacity is 12.55 mg g−1 at 25 °C. Freundlich isotherm and pseudo-second-order kinetic models fit well the adsorption data. Thermodynamics indicate that adsorption(3) is exothermic. Column regeneration was tested for three cycles and Yan et al. was found the best kinetic model.

A cobalt–carbon@silica nanocomposite was synthesized from a cobalt 2,2′-bipyridine terephthalate complex and its adsorption behavior towards crystal violet dye was tested using batch and column techniques.

A 3D hierarchical graphitic carbon nanostructure encapsulating cobalt(0)/cobalt oxide nanoparticles (CoGC) has been prepared by solid-state pyrolysis of a mixture of anthracene and cobalt 2,2′-bipyridine terephthalate complex at 850 °C. Based on the Brunauer–Emmett–Teller (BET) and Barrett–Joyner–Halenda (BJH) methods, the prepared material has high surface area (186.8 m 2 g –1 ) with an average pore width of 205.5 Å. XPS reveals the functionalization of carbon with different oxygen-containing groups, such as carboxylic acid groups. The presence of metallic cobalt nanoparticles with cubic and hexagonal crystalline structures encapsulated in graphitized carbon is confirmed using XRD and TEM. Raman spectroscopy indicates a graphitization degree of I D / I G = 1.02. CoGC was cast onto a glassy carbon electrode and used for urea electrooxidation in an alkaline solution. The electrochemical investigation shows that the newly prepared CoGC has a promising electrocatalytic activity toward urea. The specific activity is 128 mA cm –1 mg –1 for the electrooxidation of 0.3 M urea in 1 M KOH at a relatively low onset potential (0.31 V vs Ag/AgCl). It can be mainly attributed to the morphological structure of carbon and the high reactivity of cobalt nanoparticles. The calculated charge-transfer resistance, R ct , of the modified electrode in the presence of urea (10.95 Ω) is significantly lower than that in the absence of urea (113.5 Ω), which indicates electrocatalytic activity. The value of charge-transfer rate constant, k s , for the anodic reaction is 0.0058 s –1 . Electrocatalytic durability in 1000 s chronoamperometry of the modified electrode suggests high structure stability. The modified electrode retained about 60% of its activity after 100 cycles as indicated by linear sweep voltammetry.

Herein we report the B(3,4,5-F3H2C6)3-catalysed C3-allylation of indoles using allylic esters. 25 examples of C3-allylated products are presented in up to 97% yield. The mechanism for the reaction was explored...

Silica-supported hierarchical graphitic carbon sheltering cobalt nanoparticles Co-HGC@SiO2 (1) were prepared by pyrolysis at 850 °C of [Co(phen)(H2O)4]SO4·2H2O complex with silica in the presence of pyrene as a carbon source under nitrogen atmosphere. Nanocomposites (2) and (3) were obtained by acid treatment of (1) with HCl and HF acid, respectively. The nanocomposites showed rough hierarchical carbon microstructures over silica support decorated with irregular cobalt nanospheres and nanorods 50 to 200 nm in diameter. The nanoparticles consist of graphitic shells and cobalt cores. SEM, EDAX and TEM elemental mapping indicate a noticeable loss of cobalt in the case of (2) and loss of cobalt and silica in the case of (3) with an increase in porosity. Nanocomposite (3) showed the highest BET surface area 217.5 m2g−1. Raman spectrum shows defect D-band and graphitic G-band as expected in carbon nanostructures. PXRD reveals the presence of cobalt(0) nanoparticles. XPS indicates the presence of Co(II) oxides and the successful doping of nitrogen in the nanocomposites. Moreover, TEM elemental mapping provides information about the abundance of Si, Co, C, N and S elements in zones. Nanocomposite (1) showed maximum uptake capacity of 192.3 and 224.5 mg/g for crystal violet CV and methyl orange MO dyes, respectively. Nanocomposite (2) showed a capacity of 94.1 and 225.5 mg/g for CV and MO dyes, respectively. Nanocomposite (4) obtained after treatment of (1) with crystal violet proved successful adsorption of CV. Co-HGC (5) prepared without addition of silica has a capacity for CV equal to 192 mg/g, while it is 769.2 mg/g with MO. Electrostatics and π–π interactions of graphite and cobalt species in the nanocomposites with aromatic rings of cationic and anionic dyes are responsible for the adsorption. Yan et al. was the best model to describe column kinetics. The thomas column adsorption model showed that the maximum uptake capacity of (1) was 44.42 mg/g for CV and 32.62 mg/g for MO. for a column packed with 0.5 gm of (1) and dye concentration of 100 mg/L at a flow rate of 1 mL/min. The column was recycled three times with no noticeable clogging or degradation of nanocomposites. Thus, Co-HGC@SiO2 adsorbents can be used efficiently to treat water contaminated with cationic and anionic dyes.

The efficacy of boron-based catalysts has drawn considerable attention from the scientific community due to their relatively low toxicities and high selectivities. Formation of a new carbon–carbon or carbon–nitrogen bond...

3D hierarchical graphitic carbon nanowalls encapsulating cobalt nanoparticles HPC-Co were prepared in high yield from solid-state pyrolysis of cobalt 2,2′-bipyridine chloride complex. Annealing of HPC-Co in air gave HPC-CoO, which consists of a mixture of crystallite Co3O4 nanospheres and nanorods bursting out of mesoporous carbon. Both nanocomposites were fully characterized using SEM, TEM, BET, and powder X-ray diffraction. The elemental composition of both nanocomposites examined using SEM elemental mapping and TEM elemental mapping supports the successful doping of nitrogen. The powder X-ray diffraction studies supported the formation of hexagonal cobalt in HPC-Co, and cubic crystalline Co3O4 with cubic cobalt in HPC-CoO. HPC-Co and HPC-CoO can be used as a modified carbon electrode in cyclic voltammetry experiments for the detection of fructose with limit of detection LOD 0.5 mM. However, the single-frequency impedimetric method has a wider dynamic range of 8.0–53.0 mM and a sensitivity of 24.87 Ω mM−1 for the electrode modified with HPC-Co and 8.0–87.6 mM and a sensitivity of 1.988 Ω mM−1 for the electrode modified with HPC-CoO. The LOD values are 3 and 4 mM, respectively. The effect of interference increases in the following order: ascorbic acid, ethanol, urea, and glucose. A simple method was used with negligible interference from glucose to measure the percentage of fructose in a corn syrup sample with an HPC-CoO electrode. A specific capacitance of 47.0 F/g with 76.6% retentivity was achieved for HPC-Co and 28.2 F/g with 87.9% for HPC-CoO for 3000 charge–discharge cycles. Thus, (1) has better sensitivity and specific capacitance than (2), because (1) has a higher surface area and less agglomerated cobalt nanoparticles than (2).