The catalytic degradation of linear low-density (lldPE) polyethylene over HY-zeolite catalyst was studied in a semi-batch reactor. One of the important problems encountered during catalytic pyrolysis of macromolecules is the contact with the catalyst, which is known to affect the product distribution and the quality of the coke formed. A pre-degradation procedure was introduced to achieve efficient contact between the LLDPE macromolecules and the catalyst. The influence of the pre-degradation to the reaction conditions including holding time, temperature, polymer to catalyst ratio and flow rate of carrier gas was examined. Moreover, the pre-degradation results were compared with the results obtained using normal mixing procedure. The results obtained showed that, pre-degradation promotes the liquid fraction by a factor of more than one-fold increase at the expense of the gas fraction and the coke yield. The optimal liquid fraction with pre-degradation was obtained at low reaction temperature and catalyst amount respectively, i.e. high polymer to catalyst ratio, making it economically viable method for the degradation of lldPE.
Curved pipes are essential components of subsea process equipment and some part of production pipeline and riser. So far, most of the studies on of wax deposition and the possible mitigation strategies have been carried out using straight pipelines, with little attention given to curved pipes. Therefore, the objective of this study is to use an experimental flow loop designed and assembled in the lab to study and understand the mechanisms and variable parameters that affect wax depositional behaviour under the single-phase flow. Series of experiments were carried out with pipes curvatures of 0, 45 and 90-degree at different flow rates (2 and 11 L/min). The sequence in which the bends are incorporated creates non-uniformity of boundary shear, flow separation, and caused isolation of fluid around the bends that affect wax deposition, which depends on flow regimes – Reynolds number along with the radius of curvature of the bend. Prior to the flow loop experiment, the waxy crude oil was characterized by measuring the viscosity, WAT (30°C), pour point (25.5°C), n-Paraffin distribution (C10 - C67), and the saturated/aromatic/resin/asphalte (SARA) fractions Results of this study shows that the wax deposit thickness decreases at higher flow rate within the laminar (Re<2300) and turbulent (Re>2300) flow regimes. It was observed that the deposition rate was significantly higher in curved pipes, about 8 and 10% for 45 and 90-degree, respectively in comparison to the straight pipe for all flow conditions. Increase elevation of the curved pipe, however, led to a more wax deposition trend; where a higher percentage of wax deposit was observed in 45-degree compared to 90-degree curved pipe. This trend was due addition of gravity forces to the frictional forces - influenced by the physical mechanisms of wax deposition mainly molecular diffusion, shear dispersion and gravity settling. From the results of this study, a new correlation between wax deposit thickness and pressure drop was developed. A relationship was established between wax deposit thicknesses, bend angle in pipes and wax deposition mechanisms with a reasonable agreement with published data, especially for steady state condition. Therefore, this study will enhance the understanding of the wax deposition management and improve predictions for further development of a robust mitigation strategy.
Production, transportation and storage of highly waxy crude oil is very challenging. This is because they are usually characterised by high content of macro-crystalline waxes, predominantly consisting of n-alkanes (C 18 to C 36) that which could cause costly deposition within the wellbore and production equipment. The accumulation of deposited wax can decrease oil production rates, cause equipment breakdown, and clog the transport and storage facilities. Currently, different polymeric inhibitors have been utilised in the oil and gas field to mitigate and prevent wax deposition. However, as of today, there is no distinctive wax inhibitor that could work effectively for all oil fields. One of the objectives of this work is to study the efficacy of a blended commercial wax inhibitor-pour point depressant on wax deposition mitigation in a flow rig designed with 0 and 45-degree bends in the pipeline. Standard laboratory techniques using high-temperature gas chromatography (HTGC), rheometer rig, polarized microscope and elution chromatography were employed to obtain n-paraffin distribution, oil viscosity, WAT, pour point and SARA fractions. Series of experimentation were carried out with and without the inhibitor in a straight pipe test section. The severity of wax deposition in the pipeline built-in with a 45-degree bend is compared with a straight pipe. The blended inhibitor was tested at concentrations of 500, 1000, and 1500-ppm, under laminar and turbulent conditions. The crude oil sample was found to be naturally waxy with wax content of 19.75wt%, n-paraffin distributions ranges from C 15-C 74 , WAT and pour point of 30°C and 25°C respectively. The severity of wax deposition in the test section is 43% higher in 45-degree bend compared to straight pipe. However, the severity of the deposition was reduced to 12.3% at extremely low temperature and flow rate. Nonetheless, better inhibition performance was achieved at 25 and 30°C. The wax thickness was reduced from δ wax ≈ 0.36mm at 5 l/min to δ wax ≈ 0.132mm at 7 l/min at constant coolant temperature (25°C) and 1500-ppm, whereas, no wax deposition was observed at 11 l/ min. Mechanisms such as molecular diffusion due to frictional pressure losses, shear dispersion and gravity settling due to momentum change and hydrostatic, alongside with thermal difference are the main drivers for wax deposition in both straight and bend pipe. Whereas, the interaction mechanisms such as the nucleation, alongside with adsorption, co-crystallization, and solubilisation between the new blended inhibitor and the wax crystals provide an improved inhibition performance in the system even at extreme cases.
The separation of produced fluids is essential once it reaches the surface. This separation is achieved in gravity separators. The design and sizing of separators can be challenging due to the number of factors involved. Improper separator design can bottleneck and reduce the production of the entire facility. This paper describes the development of a capital cost optimisation model for sizing three phase separators. The developed model uses GRG Non-linear algorithms to determine the minimum cost associated with the construction of horizontal separators subject to four sets of constraints. A numerical sizing example was solved to provide the details associated with the model and the ease with which parameters can be varied to suit the user's needs. Finally, a spreadsheet comparison between results obtained from the developed model and four other extant models is carried out. Results indicated that the developed model predicted results within an absolute error of AE5m 3 in most cases and a maximum of AE12.5m 3 for very high gas flows in comparison to conventional models developed based on retention time theory.
A mechanistic model on catalyst deactivation by coke formation in a continuous stirred tank reactor (CSTR) has been developed in the paper. Catalyst deactivation by coke formation was treated as a surface reaction. Four reaction mechanisms representing coke formation through different routes were proposed. The evolved system of ordinary differential equations (ODEs) was solved numerically using MATLAB. This approach was validated by applying it to the skeletal isomerization of 1-pentene over ferrierite. Simulation results were compared qualitatively to those obtained from the literature. Simulation results indicated that coke formation is an extremely rapid process with fast formation of coke components on the strongest acid sites leading to final coke. The coke deposition is slower at higher residence times resulting in more stable product formation and weaker deactivation. The results obtained from this work revealed that the developed model is indeed able to successfully demonstrate the most essential features of catalyst deactivation by coke formation and are in agreement with the findings in the literature. Future work is aimed to extend the study to different reactors such as a plug flow reactor, in addition to analysis of the reaction system’s sensitivity to variables such as temperature and pressure.
Summary In the first part of this work, the development of a capital cost optimization model for sizing three-phase separators was described. The developed model uses generalized reduced gradient nonlinear algorithms to determine the minimum cost associated with the construction of horizontal separators subject to four sets of constraints. In the second part, an experimental test rig was designed and used to investigate the effect of gas flow rate, liquid flow rate, and slenderness ratio (L/D) on the separation performance of horizontal three-phase separators. The results indicated an inverse relationship between an increase in gas and liquid flow rate and the separator outlet quality. It also indicated a direct relationship between an increase in slenderness ratio and separator outlet quality. The results also showed that the gradient change of the percentage of water in the oil outlet with respect to slenderness ratio decreased to ratios of 6:1. Hence, the separation rate increased. At ratios greater than 6:1, the separation still increases, but the gradient change in separation drops off, implying that the benefit in terms of separation is diminishing beyond this point. Therefore, the optimal slenderness ratio for technical reasons is 6:1.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
334 Leonard St
Brooklyn, NY 11211
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.