In this work we uncover a novel effect between concentration dependent ion pair formation and anion stability at reducing potentials, e.g., at the metal anode. Through comprehensive calculations using both first-principles as well as well-benchmarked classical molecular dynamics over a matrix of electrolytes, covering solvents and salt anions with a broad range in chemistry, we elucidate systematic correlations between molecular level interactions and composite electrolyte properties, such as electrochemical stability, solvation structure, and dynamics. We find that Mg electrolytes are highly prone to ion pair formation, even at modest concentrations, for a wide range of solvents with different dielectric constants, which have implications for dynamics as well as charge transfer. Specifically, we observe that, at Mg metal potentials, the ion pair undergoes partial reduction at the Mg cation center (Mg(2+) → Mg(+)), which competes with the charge transfer mechanism and can activate the anion to render it susceptible to decomposition. Specifically, TFSI(-) exhibits a significant bond weakening while paired with the transient, partially reduced Mg(+). In contrast, BH4(-) and BF4(-) are shown to be chemically stable in a reduced ion pair configuration. Furthermore, we observe that higher order glymes as well as DMSO improve the solubility of Mg salts, but only the longer glyme chains reduce the dynamics of the ions in solution. This information provides critical design metrics for future electrolytes as it elucidates a close connection between bulk solvation and cathodic stability as well as the dynamics of the salt.

When designing a high energy density battery, one of the critical features is a high voltage, high capacity cathode material. In the development of Mg batteries, oxide cathodes that can reversibly intercalate Mg, while at the same time being compatible with an electrolyte that can deposit Mg reversibly are rare. Herein, we report the compatibility of Mg anodes with α-V 2 O 5 by employing magnesium bis(trifluoromethane sulfonyl)imide in diglyme electrolytes at very low water levels. Electrolytes that contain a high water level do not reversibly deposit Mg, but interestingly these electrolytes appear to enable much higher capacities for an α-V 2 O 5 cathode. Solid state NMR indicates that the major source of the higher capacity in high water content electrolytes originates from reversible proton insertion. In contrast, we found that lowering the water level of the magnesium bis(trifluoromethane sulfonyl)imide in diglyme electrolyte is critical to achieve reversible Mg deposition and direct evidence for reversible Mg intercalation is shown. Findings we report here elucidate the role of proton intercalation in water-containing electrolytes and clarify numerous conflicting reports of Mg insertion into α-V 2 O 5 .

We developed a unique class of non-Grignard, aluminum-free magnesium electrolytes based on a simple mixture of magnesium compounds: magnesium hexamethyldisilazide (Mg(HMDS)2) and magnesium chloride (MgCl2).

Mg battery operates with Chevrel phase (Mo6S8, ∼1.1 V vs Mg) cathodes that apply Grignard-based or derived electrolytes, which allow etching of the passivating oxide coating forms at the magnesium metal anode. Majority of Mg electrolytes studied to date are focused on developing new synthetic strategies to achieve a better reversible Mg deposition. While most of these electrolytes contain chloride as a component, and there is a lack of literature which investigates the fundamental role of chloride in Mg electrolytes. Further, ease of preparation and potential safety benefits have made simple design of magnesium electrolytes an attractive alternative to traditional air sensitive Grignard reagents-based electrolytes. Work presented here describes simple, non-Grignard magnesium electrolytes composed of magnesium bis(trifluoromethane sulfonyl)imide mixed with magnesium chloride (Mg(TFSI)2-MgCl2) in tetrahydrofuran (THF) and diglyme (G2) that can reversibly plate and strip magnesium. Based on this discovery, the effect of chloride in the electrolyte complex was investigated. Electrochemical properties at different initial mixing ratios of Mg(TFSI)2 and MgCl2 showed an increase of both current density and columbic efficiency for reversible Mg deposition as the fraction content of MgCl2 increased. A decrease in overpotential was observed for rechargeable Mg batteries with electrolytes with increasing MgCl2 concentration, evidenced by the coin cell performance. In this work, the fundamental understanding of the operation mechanisms of rechargeable Mg batteries with the role of chloride content from electrolyte could potentially bring rational design of simple Mg electrolytes for practical Mg battery.

Functional multivalent intercalation cathodes represent one of the largest hurdles in the development of Mg batteries. While there are many reports of Mg cathodes, many times the evidence of intercalation chemistry is only circumstantial. In this work, direct evidence of Mg intercalation into a bilayer structure of V2O5·nH2O xerogel is confirmed, and the nature of the Mg intercalated species is reported. The interlayer spacing of V2O5·nH2O contracts upon Mg intercalation and expands for Mg deintercalation due to the strong electrostatic interaction between the divalent cation and the cathode. A combination of NMR, pair distribution function (PDF) analysis, and X-ray absorption near edge spectroscopy (XANES) confirmed reversible Mg insertion into the V2O5·nH2O material, and structural evolution of Mg intercalation leads to the formation of multiple new phases. Structures of V2O5·nH2O with Mg intercalation were further supported by the first principle simulations. A solvent cointercalated Mg in V2O5·nH2O is observed for the first time, and the 25Mg magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy was used to elucidate the structure obtained upon electrochemical cycling. Specifically, existence of a well-defined Mg–O environment is revealed for the Mg intercalated structures. Information reported here reveals the fundamental Mg ion intercalation mechanism in a bilayer structure of V2O5·nH2O material and provides insightful design metrics for future Mg cathodes.

Development of Mg electrolytes that can plate/strip Mg is not trivial and remains one of the major roadblocks to advance Mg battery research.

New energy storage chemistries based on Mg ions or Ca ions can theoretically improve both the energy density and reduce the costs of batteries. To date there has been limited progress in implementing these systems due to the challenge of finding a high voltage high capacity cathode that is compatible with an electrolyte that can plate and strip the elemental metal. In order to accelerate the discovery of such a system, model systems are needed that alleviate some of the issues of incompatibility. This report demonstrates the ability of nickel hexacyanoferrate to electrochemically intercalate Mg, Ca and Zn ions from a nonaqueous electrolyte. This material has a relatively high insertion potential and low overpotential in the electrolytes used in this study. Furthermore, since it is not an oxide based cathode it should be able to resist attack by corrosive electrolytes such as the chloride containing electrolytes that are often used to plate and strip magnesium. This makes it an excellent cathode for use in developing and understanding the complex electrochemistry of multivalent ion batteries.

We report an approach to control the reversible electrochemical activity (i.e., extraction/insertion) of Mg(2+) in a cathode host through the use of phase-pure epitaxially stabilized thin film structures. The epitaxially stabilized MgMn2O4 (MMO) thin films in the distinct tetragonal and cubic phases are shown to exhibit dramatically different properties (in a nonaqueous electrolyte, Mg(TFSI)2 in propylene carbonate): tetragonal MMO shows negligible activity while the cubic MMO (normally found as polymorph at high temperature or high pressure) exhibits reversible Mg(2+) activity with associated changes in film structure and Mn oxidation state. These results demonstrate a novel strategy for identifying the factors that control multivalent cation mobility in next-generation battery materials.