No abstract

Collagen type I, commonly derived from xenogenic sources, is extensively used as a biomaterial for tissue engineering applications. However, the use of xenogenic collagen is typically associated with species specific variation in mechanical, structural, and biological properties that are known to influence cellular response and remodeling. In addition, immunological complications and risks of disease transmission are also major concerns. The goal of this study is to characterize a new xeno-free human skin-derived collagen and assess its applicability as a bioink for cell-laden 3 D bioprinting. Four different concentrations of human collagen (i.e., 0.5 mg/mL, 1 mg/mL, 3 mg/mL and 6 mg/mL) were employed for the synthesis of collagen hydrogels. In addition, bovine collagen was used as a xenogenic control. Results from SDS-PAGE analysis showed the presence of α1, α2, and β chains, confirming that the integrity of type I human collagen is maintained post isolation. Polymerization rate and compressive modulus increased significantly with increase in the concentration of human collagen. When comparing two different sources of collagen, the polymerization rate of xenogenic collagen was significantly faster (p < 0.05) than human collagen while the compressive modulus was comparable. Raman spectroscopy showed a large peak in the Amide I band around 1600 cm−1, indicating a dense and supraorganized fibrillar structure in human collagen hydrogels. Conversely, Amide I band intensity for xenogenic collagen was comparable to that of Amide II and Amide III bands. Further, the use of 6 mg/mL human collagen as a bioink yielded 3 D printed constructs with high shape fidelity and cell viability. On the other hand, xenogenic collagen failed to yield stable 3 D printed constructs. Together, the results from this study provides an impetus for using human-derived collagen as a viable alternative to xenogenic sources for 3 D bioprinting of clinically relevant scaffolds for tissue engineering applications.

Bioactive three-dimensional (3D) printed scaffolds are promising candidates for bone tissue engineering (BTE) applications. Here, we introduce a bioactive ink composed of Bioglass 45S5 (BG) and methacrylated collagen (CMA) for 3D printing of biomimetic constructs that resemble the organic and inorganic composition of native bone tissue. A uniform dispersion of BG particles within the collagen network improved stability and reduced swelling of collagen hydrogels. Rheological testing showed significant improvement in the yield stress and percent recovery of 3D printed constructs upon BG incorporation. Further, addition of BG improved the bone bioactivity of 3D printed constructs in stimulated body fluid. BG incorporated CMA (BG-CMA) constructs maintained high cell viability and enhanced alkaline phosphatase activity of human mesenchymal stem cells. In addition, cell-mediated calcium deposition was significantly higher on BG-CMA constructs, compared to CMA alone. In conclusion, 3D printed BG-CMA constructs have significant potential for use in BTE applications.

Xenogeneic sources of collagen type I remain a common choice for regenerative medicine applications due to ease of availability. Human and animal sources have some similarities, but small variations in amino acid composition can influence the physical properties of collagen, cellular response, and tissue remodeling. The goal of this work is to compare human collagen type I‐based hydrogels versus animal‐derived collagen type I‐based hydrogels, generated from commercially available products, for their physico‐chemical properties and for tissue engineering and regenerative medicine applications. Specifically, we evaluated whether the native human skin type I collagen could be used in the three most common research applications of this protein: as a substrate for attachment and proliferation of conventional 2D cell culture; as a source of matrix for a 3D cell culture; and as a source of matrix for tissue engineering. Results showed that species and tissue specific variations of collagen sources significantly impact the physical, chemical, and biological properties of collagen hydrogels including gelation kinetics, swelling ratio, collagen fiber morphology, compressive modulus, stability, and metabolic activity of hMSCs. Tumor constructs formulated with human skin collagen showed a differential response to chemotherapy agents compared to rat tail collagen. Human skin collagen performed comparably to rat tail collagen and enabled assembly of perfused human vessels in vivo. Despite differences in collagen manufacturing methods and supplied forms, the results suggest that commercially available human collagen can be used in lieu of xenogeneic sources to create functional scaffolds, but not all sources of human collagen behave similarly. These factors must be considered in the development of 3D tissues for drug screening and regenerative medicine applications.

No abstract