Gecko adhesion has become a paradigmatic example of bio-inspired engineering, yet among the many gecko-like synthetic adhesives (GSAs), truly gecko-like performance remains elusive. Many GSAs have previously demonstrated one or two features of the gecko adhesive. We present a new wedge-shaped GSA that exhibits several gecko-like properties simultaneously: directional features; zero force at detachment; high ratio of detachment force to preload force; non-adhesive default state; and the ability to maintain performance while sliding, even after thousands of cycles. Individual wedges independently detach and reattach during sliding, resulting in high levels of shear and normal adhesion during drag. This behaviour provides a non-catastrophic failure mechanism that is desirable for applications such as climbing robots where sudden contact failure would result in serious falls. The effects of scaling patch sizes up to tens of square centimetres are also presented and discussed. Patches of 1 cm 2 had an adhesive pressure of 5.1 kPa while simultaneously supporting 17.0 kPa of shear. After 30 000 attachment/detachment cycles, a patch retained 67 per cent of its initial adhesion and 76 per cent of its initial shear without cleaning. Square-based wedges of 20 mm and 50 mm are manufactured in a moulding process where moulds are fabricated using a dual-side, dual-angle lithography process on quartz wafers with SU-8 photoresist as the mould material and polydimethylsiloxane as the cast material.

Limbless organisms like snakes can navigate nearly all terrain. In particular, desert-dwelling sidewinder rattlesnakes (C. cerastes) operate effectively on inclined granular media (like sand dunes) that induce failure in field-tested limbless robots through slipping and pitching. Our laboratory experiments reveal that as granular incline angle increases, sidewinder rattlesnakes increase the length of their body in contact with the sand. Implementing this strategy in a physical robot model of the snake enables the device to ascend sandy slopes close to the angle of maximum slope stability. Plate drag experiments demonstrate that granular yield stresses decrease with increasing incline angle. Together these three approaches demonstrate how sidewinding 1 arXiv:1410.2945v1 [physics.bio-ph] 11 Oct 2014 with contact-length control mitigates failure on granular media.The majority of terrestrial mobile robots are restricted to laboratory environments, in part because such robots are designed to roll on hard flat surfaces. It is difficult to systematically improve such terrestrial robots because we lack understanding of the physics of interaction with complex natural substrates like sand, dirt and tree bark. We are thus limited in our ability to computationally explore designs for potential all-terrain vehicles; in contrast, many of the recent developments in aerial and aquatic vehicles have been enabled by sophisticated computationaldynamics tools that allow such systems to be designed in silico (1).Compared with human-made devices, organisms such as snakes, lizards, and insects move effectively in nearly all natural environments. In recent years, scientists and engineers have sought to systematically discover biological principles of movement and implement these in robots (2). This "bioinspired robotics" approach (3) has proved fruitful to design laboratory robots with new capabilities (new gaits, morphologies, control schemes) including rapid running (2, 4), slithering (5), flying (6), and swimming in sand (7). Fewer studies have transferred biological principles into robust field-ready devices (4, 8) capable of operating in, and interacting with, natural terrain.Limbless locomotors like snakes are excellent systems to study to advance real-world allterrain mobility. Snakes are masters of most terrains: they can move rapidly on land (9, 10) and through water (11), burrow and swim through sand and soil (12), slither through tiny spaces (13), climb complex surfaces (14), and even glide through the air (15). Relative to legged locomotion, limbless locomotion is less studied, and thus broad principles which govern multi-environment movement are lacking. Recently developed limbless robotic platforms (5), based generally on the snake body plan, are appealing for multi-functional robotics study because they are also capable of a variety of modes of locomotion. These robots can traverse confined spaces, climb trees and pipes, and potentially dive through loose material. However, 2 the gaits that carry these robots across fir...

High dry friction requires intimate contact between two surfaces and is generally obtained using soft materials with an elastic modulus less than 10 MPa. We demonstrate that high-friction properties similar to rubberlike materials can also be obtained using microfiber arrays constructed from a stiff thermoplastic (polypropylene, 1 GPa). The fiber arrays have a smaller true area of contact than a rubberlike material, but polypropylene's higher interfacial shear strength provides an effective friction coefficient of greater than 5 at normal loads of 8 kPa. At the pressures tested, the fiber arrays showed more than an order of magnitude increase in shear resistance compared to the bulk material. Unlike softer materials, vertical fiber arrays of stiff polymer demonstrate no measurable adhesion on smooth surfaces due to high tensile stiffness.

Geckos use millions of adhesive setae on their toes to climb vertical surfaces at speeds of over 1 m s K1 . Climbing presents a significant challenge for an adhesive since it requires both strong attachment and easy, rapid removal. Conventional pressure-sensitive adhesives are either strong and difficult to remove (e.g. duct tape) or weak and easy to remove (e.g. sticky notes). We discovered that the energy required to detach adhering tokay gecko setae (W d ) is modulated by the angle (q) of a linear path of detachment. Gecko setae resist detachment when dragged towards the animal during detachment (qZ308) requiring W d Z5.0G 0.86 (s.e.) J m K2 to detach, largely due to frictional losses. This external frictional loss is analogous to viscous internal frictional losses during detachment of pressure-sensitive adhesives. We found that, remarkably, setae possess a built-in release mechanism. Setae acted as springs when loaded in tension during attachment and returned elastic energy when detached along the optimal path (qZ1308), resulting in W d ZK0.8G0.12 J m K2 . The release of elastic energy from the setal shaft probably causes spontaneous release, suggesting that curved shafts may enable easy detachment in natural, and synthetic, gecko adhesives.

If geckos had not evolved, it is possible that humans would never have invented adhesive nanostructures. Geckos use millions of adhesive setae on their toes to climb vertical surfaces at speeds of over 1 m s K1 . Climbing presents a significant challenge for an adhesive in requiring both strong attachment and easy rapid removal. Conventional pressure-sensitive adhesives (PSAs) are either strong and difficult to remove (e.g. duct tape) or weak and easy to remove (e.g. sticky notes). The gecko adhesive differs dramatically from conventional adhesives. Conventional PSAs are soft viscoelastic polymers that degrade, foul, self-adhere and attach accidentally to inappropriate surfaces. In contrast, gecko toes bear angled arrays of branched, hair-like setae formed from stiff, hydrophobic keratin that act as a bed of angled springs with similar effective elastic modulus to that of PSAs. Setae are self-cleaning and maintain function for months during repeated use in dirty conditions. Setae are an anisotropic 'frictional adhesive' in that adhesion requires maintenance of a proximally directed shear load, enabling either a tough bond or spontaneous detachment. Gecko-like synthetic adhesives may become the glue of the future-and perhaps the screw of the future as well.