We present a microfluidic device capable of separating platelets from other blood cells in continuous flow using dielectrophoresis field-flow-fractionation. The use of hydrodynamic focusing in combination with the application of a dielectrophoretic force allows the separation of platelets from red blood cells due to their size difference. The theoretical cell trajectory has been calculated by numerical simulations of the electrical field and flow speed, and is in agreement with the experimental results. The proposed device uses the so-called "liquid electrodes" design and can be used with low applied voltages, as low as 10 V(pp). The obtained separation is very efficient, the device being able to achieve a very high purity of platelets of 98.8% with less than 2% cell loss. Its low-voltage operation makes it particularly suitable for point-of-care applications. It could further be used for the separation of other cell types based on their size difference, as well as in combination with other sorting techniques to separate multiple cell populations from each other.

We present a device capable of electrical cell lysis and evaluation of lysis efficiency in continuous flow using dielectrophoretic cell sorting. We use a combination of AC electrical fields and so-called liquid electrodes to avoid bubble creation at the electrode surface. The electrical field distribution is calculated in different electrode configurations by numerical simulations. Cell sorting shows high lysis efficiency, 99% of yeast cells sorted after lysis featuring dielectric properties similar to dead cells. A study of the potential device throughput is performed.

This work combines the power of 3D additive manufacturing with clinically advantageous minimally invasive delivery. We obtain porous, highly compressible and mechanically rugged structures by optimizing a cryogenic 3D printing process. Only a basic commercial 3D printer and elementary control over reaction rate and freezing are required. The porous hydrogels obtained are capable of withstanding delivery through capillaries up to 50 times smaller than their largest linear dimension, an as yet unprecedented compression ratio. Cells seeded onto the hydrogels are protected during compression. The hydrogel structures further exhibit excellent biocompatibility 3 months after subcutaneous injection into mice. We finally demonstrate that local modulation of pore size grants control over vascularization density in vivo. This provides proof-of-principle that meaningful biological information can be encoded during the 3D printing process, deploying its effect after minimally invasive implantation.

Plasma membrane tension and the pressure generated by actin polymerization are two antagonistic forces believed to define the protrusion rate at the leading edge of migrating cells [1-5]. Quantitatively, resistance to actin protrusion is a product of membrane tension and mean local curvature (Laplace's law); thus, it depends on the local geometry of the membrane interface. However, the role of the geometry of the leading edge in protrusion control has not been yet investigated. Here, we manipulate both the cell shape and substrate topography in the model system of persistently migrating fish epidermal keratocytes. We find that the protrusion rate does not correlate with membrane tension, but, instead, strongly correlates with cell roundness, and that the leading edge of the cell exhibits pinning on substrate ridges-a phenomenon characteristic of spreading of liquid drops. These results indicate that the leading edge could be considered a triple interface between the substrate, membrane, and extracellular medium and that the contact angle between the membrane and the substrate determines the load on actin polymerization and, therefore, the protrusion rate. Our findings thus illuminate a novel relationship between the 3D shape of the cell and its dynamics, which may have implications for cell migration in 3D environments.

No abstract

No abstract

Actin-myosin microfilament bundles or stress-fibers are the principal tension-generating structures in the cell. Their mechanical properties are critical for cell shape, motion, and interaction with other cells and extracellular matrix, but were so far difficult to access in a living cell. Here we propose a micro-fabricated two-component setup for direct tension measurement on a peripheral bundle within an intact cell. We used 3-D substrates made of silicon elastomer to elevate the cell making the filament bundle at its border accessible from the side, and employed an ultra-soft (spring constant 0.78 nN μm(-1)) epoxy-based cantilever for mechanical probing. With this setup we were able for the first time to measure the tension in peripheral actin bundles in living primary fibroblasts spread on a rigid substrate.

No abstract