No abstract

Bacteria of the Bacillus cereus family form highly resistant spores, which in the case of the pathogen B. anthracis act as the agents of infection. The outermost layer, the exosporium, enveloping spores of the B. cereus family as well as a number of Clostridia, plays roles in spore adhesion, dissemination, targeting, and germination control. We have analyzed two naturally crystalline layers associated with the exosporium, one representing the "basal" layer to which the outermost spore layer ("hairy nap") is attached, and the other likely representing a subsurface ("parasporal") layer. We have used electron cryomicroscopy at a resolution of 0.8-0.6 nm and circular dichroism spectroscopic measurements to reveal a highly α-helical structure for both layers. The helices are assembled into 2D arrays of "cups" or "crowns." High-resolution atomic force microscopy of the outermost layer showed that the open ends of these cups face the external environment and the highly immunogenic collagen-like fibrils of the hairy nap (BclA) are attached to this surface. Based on our findings, we present a molecular model for the spore surface and propose how this surface can act as a semipermeable barrier and a matrix for binding of molecules involved in defense, germination control, and other interactions of the spore with the environment.electron crystallography | cryoelectron microscopy | two-dimensional crystal

The physical properties of semicrystalline polymers depend on the organisation of chains within the crystal and amorphous regions, on the interface between the two, and on the location and nature of defects. Here, torsional tapping atomic force microscopy has been used to image crystalline lamellae and the crystal-amorphous-region interface at the single-chain level with resolution down to 3.7 Å. Defects within the crystalline phase, such as buried folds and chain ends, are revealed. Imaging at the chain level also allows direct measurement of crystalline stem lengths, providing a potential route to test theories of crystal thickness selection.

Torsional-tapping AFM with supersharp carbonwhisker tips is used to explore the molecular conformations at the surface of a semicrystalline polymer. Images of the crystal− amorphous interface of oriented polyethylene have allowed us to measure hitherto inaccessible parameters that can be directly compared to polymer crystallization theories and molecular simulations, such as the length of stem-to-stem overhang. It has also been possible to identify both first-and second-neighbor folds and to determine the surface roughness of lamellae which we find approximately doubles the interfacial area. Finally, we calculate the interfacial density profile from the images and find it to be sigmoidal but narrower than values reported by SAXS measurements.

The nanoscale mechanical properties of live Staphylococcus aureus cells during different phases of growth were studied by atomic force microscopy. Indentation to different depths provided access to both local cell wall mechanical properties and whole-cell properties, including a component related to cell turgor pressure. Local cell wall properties were found to change in a characteristic manner throughout the division cycle. Splitting of the cell into two daughter cells followed a local softening of the cell wall along the division circumference, with the cell wall on either side of the division circumference becoming stiffer. Once exposed, the newly formed septum was found to be stiffer than the surrounding, older cell wall. Deeper indentations, which were affected by cell turgor pressure, did not show a change in stiffness throughout the division cycle, implying that enzymatic cell wall remodeling and local variations in wall properties are responsible for the evolution of cell shape through division.

The function of bioenergetic membranes is strongly influenced by the spatial arrangement of their constituent membrane proteins. Atomic force microscopy (AFM) can be used to probe protein organization at high resolution, allowing individual proteins to be identified. However, previous AFM studies of biological membranes have typically required that curved membranes are ruptured and flattened during sample preparation, with the possibility of disruption of the native protein arrangement or loss of proteins. Imaging native, curved membranes requires minimal tip–sample interaction in both lateral and vertical directions. Here, long-range tip–sample interactions are reduced by optimizing the imaging buffer. Tapping mode AFM with high-resonance-frequency small and soft cantilevers, in combination with a high-speed AFM, reduces the forces due to feedback error and enables application of an average imaging force of tens of piconewtons. Using this approach, we have imaged the membrane organization of intact vesicular bacterial photosynthetic “organelles”, chromatophores. Despite the highly curved nature of the chromatophore membrane and lack of direct support, the resolution was sufficient to identify the photosystem complexes and quantify their arrangement in the native state. Successive imaging showed the proteins remain surprisingly static, with minimal rotation or translation over several-minute time scales. High-order assemblies of RC-LH1-PufX complexes are observed, and intact ATPases are successfully imaged. The methods developed here are likely to be applicable to a broad range of protein-rich vesicles or curved membrane systems, which are an almost ubiquitous feature of native organelles.

Calibration of lateral forces and displacements has been a long standing problem in lateral force microscopies. Recently, it was shown by Wagner et al. that the thermal noise spectrum of the first torsional mode may be used to calibrate the deflection sensitivity of the detector. This method is quick, non-destructive and may be performed in situ in air or liquid. Here we make a full quantitative comparison of the lateral inverse optical lever sensitivity obtained by the lateral thermal noise method and the shape independent method developed by Anderson et al. We find that the thermal method provides accurate results for a wide variety of rectangular cantilevers, provided that the geometry of the cantilever is suitable for torsional stiffness calibration by the torsional Sader method, in-plane bending of the cantilever may be eliminated or accounted for and that any scaling of the lateral deflection signal between the measurement of the lateral thermal noise and the measurement of the lateral deflection is eliminated or corrected for. We also demonstrate that the thermal method may be used to characterize the linearity of the detector signal as a function of position, and find a deviation of less than 8% for the instrument used.

No abstract