In this study, polyethersulfone (PES) and polyvinylidene fluoride (PVDF) microfiltration membranes containing polyvinylpyrrolidone (PVP) with and without support layers of 130 and 150 μm thickness are manufactured using the phase inversion method and then experimentally characterised. For the characterisation of membranes, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and pore size analysis are performed, the contact angle and water content of membranes are measured and the tensile test is applied to membranes without support layers. Using the results obtained from the tensile tests, the mechanical properties of the halloysite nanotube (HNT) and nano-silicon dioxide (nano SiO2) reinforced nanocomposite membranes are approximately determined by the Mori–Tanaka homogenisation method without applying any further mechanical tests. Then, plain polymeric and PES and PVDF based nanocomposite membranes are modelled using the finite element method to determine the effect of the geometry of the membrane on the mechanical behaviour for fifteen different geometries. The modelled membranes compared in terms of three different criteria: equivalent stress (von Mises), displacement, and in-plane principal strain. Based on the data obtained from the characterisation part of the study and the numerical analysis, the membrane with the best performance is determined. The most appropriate shape and material for a membrane for water treatment is specified as a 1% HNT doped PVDF based elliptical membrane.
Catalytic effect of the ferric hydroxides on the oxidation of ferrous iron by aeration has been demonstrated and the kinetics of this catalytic reaction has been formulated by the recent studies. It has been reported that the oxidation rate is linearly increasing with Fe(III) concentrations up to 100 mg/l.
In this study, the oxidation of Fe(II) is studied in batch reactors in which the concentration of Fe(III) was in the range of 0-600 mg/l. A quadratic equation has been given to determine the catalytic reaction rate constant as a function of Fe(III) concentration. It was experimentally demonstrated that there was no significant effect of Fe(III) on the ferrous iron oxidation at Fe(III) concentrations beyond 600 mg/l.
In this study, four different membranes were fabricated by using polyetherimide and polyacrylonitrile polymers, N-methyl-2-pyrrolidone and polyvinylpyrrolidone (PVP) via phase inversion method to improve the membrane performance in fruit juice wastewater (FJWW) treatment. The addition of PVP to the casting solution increased membrane hydrophilicity, water content, contact angle, porosity, Fourier transform infrared spectroscopy peaks, membrane thickness, average roughness and viscosity of cast solutions compared to the bare membrane. It can be said that the addition of a lower polymer concentration and PVP intensively increases the pure water flux of the membrane. However, as the flux increased, a small decrease in FJWW rejection was observed.
To investigate the effect of polyvinylpyrrolidone (PVP) addition and consequently porosity, two different sets of membranes are manufactured, since PVP is a widely used poring agent which has an impact on the mechanical properties of the membrane material. The first set (PAN 1) includes polyacrylonitrile (PAN) and the necessary solvent while the second set (PAN 2) is made of PAN and PVP. These membranes are put through several characterisation processes including tensile testing. The obtained data are used to model the static behaviour of the membranes with different geometries but similar loading and boundary conditions that represent their operating conditions. This modelling process is undertaken by using the finite element method. The main idea is to investigate how geometry affects the load-carrying capacity of the membranes. Alongside membrane modelling, their materials are modelled with representative elements with hexagonal and rectangular pore arrays (RE) to understand the impact of porosity on the mechanical properties. Exploring the results, the best geometry is found as the elliptic membrane with the aspect ratio 4 and the better RE as the hexagonal array which can predict the elastic properties with an approximate error of 12%.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.