A laser-mediated methodology for standoff infrared detection of threat chemicals is described in this article. Laser-induced thermal emissions (LITE) from vibrationally excited residue of highly energetic material (HEM) deposited on substrates were detected remotely. Telescope-based Fourier transform infrared (FT-IR) spectroscopy measurements were carried out on substrates containing small amounts of HEM at surface concentrations of 5-200 μg/cm(2). Target substrates of various thicknesses were heated remotely using a carbon dioxide laser, and their mid-infrared (mid-IR), thermally stimulated emission spectra were recorded after heating. The telescope was configured from reflective optical elements to minimize emission losses in the mid-IR frequencies. Spectral replicas were acquired at distances from 4 to 64 m using an FT-IR interferometer at 4 cm(-1) resolution. The laser power, laser exposure times, and acquisition time of the FT-IR interferometer were adjusted to improve the detection and identification of samples. The advantages of increasing the thermal emission were easily observed in the results. The signal intensities were proportional to the thickness of the coated surface (a function of the surface concentration) as well as the laser power and laser exposure time. The limits of detection obtained for the HEM studied were 140-21 μg/cm(2) at 4 m. Detection was achieved at 64 m for a surface concentration of 200 μg/cm(2).

Quantum cascade laser spectroscopy was used to quantify active pharmaceutical ingredient content in a model formulation. The analyses were conducted in non-contact mode by mid-infrared diffuse reflectance. Measurements were carried out at a distance of 15 cm, covering the spectral range 1000-1600 cm(-1) Calibrations were generated by applying multivariate analysis using partial least squares models. Among the figures of merit of the proposed methodology are the high analytical sensitivity equivalent to 0.05% active pharmaceutical ingredient in the formulation, high repeatability (2.7%), high reproducibility (5.4%), and low limit of detection (1%). The relatively high power of the quantum-cascade-laser-based spectroscopic system resulted in the design of detection and quantification methodologies for pharmaceutical applications with high accuracy and precision that are comparable to those of methodologies based on near-infrared spectroscopy, attenuated total reflection mid-infrared Fourier transform infrared spectroscopy, and Raman spectroscopy.

A simple, remote-sensed method of detection of traces of petroleum in soil combining artificial intelligence (AI) with mid-infrared (MIR) laser spectroscopy is presented. A portable MIR quantum cascade laser (QCL) was used as an excitation source, making the technique amenable to field applications. The MIR spectral region is more informative and useful than the near IR region for the detection of pollutants in soil. Remote sensing, coupled with a support vector machine (SVM) algorithm, was used to accurately identify the presence/absence of traces of petroleum in soil mixtures. Chemometrics tools such as principal component analysis (PCA), partial least square-discriminant analysis (PLS-DA), and SVM demonstrated the effectiveness of rapidly differentiating between different soil types and detecting the presence of petroleum traces in different soil matrices such as sea sand, red soil, and brown soil. Comparisons between results of PLS-DA and SVM were based on sensitivity, selectivity, and areas under receiver-operator curves (ROC). An innovative statistical analysis method of calculating limits of detection (LOD) and limits of decision (LD) from fits of the probability of detection was developed. Results for QCL/PLS-DA models achieved LOD and LD of 0.2% and 0.01% for petroleum/soil, respectively. The superior performance of QCL/SVM models improved these values to 0.04% and 0.003%, respectively, providing better identification probability of soils contaminated with petroleum.

Mid-infrared (MIR) laser spectroscopy was used to detect the presence of residues of high explosives (HEs) on fabrics. The discrimination of the vibrational signals of HEs from a highly MIR-absorbing substrate was achieved by a simple and fast spectral evaluation without preparation of standards using the classical least squares (CLS) algorithm. Classical least squares focuses on minimizing the differences between the spectral features of the actual spectra acquired using MIR spectroscopy and the spectral features of calculated spectra modeled from linear combinations of the spectra of neat components: HEs, fabrics, and bias. Samples in several combinations of cotton fabrics/HEs were used to validate the methodology. Several experiments were performed focusing on binary, ternary, and quaternary mixtures of TNT, RDX, PETN, and fabrics. The parameters obtained from linear combinations of the calculated spectra were used to perform discrimination analyses and to determine the sensitivity and selectivity of HEs with respect to the substrates and to each other. However, discrimination analysis was not necessary to achieve successful detection of HEs on cotton fabric substrates. The RDX signals ( m > 0.02 mg) on cotton were used to calculate the limit of detection (LOD). The signal-to-noise ratios (S/N) calculated from the spectra of cotton dosed with decreasing masses of RDX until S/N ≈ 3 resulted in a LOD of 15-33 µg, depending on the vibrational band used. Linear fits generated by comparing the mass dosed RDX with the fraction predicted were also used to calculate the LOD based on the uncertainty of the blank and the slope. This procedure resulted in a LOD of 58 µg. Probably the most representative value of the method LOD was calculated using an interpolation of a threshold determined using the predicted average value for the blank plus 3.28 times the standard deviations ( p-value threshold) for low surface dosages of RDX (LOD = 40 µg). The contribution demonstrates that to achieve HE detection on fabrics using the proposed algorithm, i.e., determining the presence/absence of HEs on the substrates, the library must contain the spectra of HEs, substrates, and potential interferents or that these spectra be added to the models in the field. If the model does not contain the spectra of the fabric components, there is a high probability of finding false positives for clean samples (no HEs) and a low probability for failed detection in samples with HEs. More work will be required to demonstrate that these new approaches to HE detection work on real-world samples and when contaminating materials are present in the samples.