In view of the importance of accurately measuring the relative density of a selective laser melted (SLMed) part for optimizing the selective laser melting (SLM) processing parameters, suitable procedures of the Archimedes method considering the surface-connected cavities were proposed by comparing the results using the Archimedes method with image analysis. The effects of the SLM processing parameters on the relative density of AlSi10Mg were investigated using the proposed procedures of the Archimedes methods and image analysis. Fourteen SLMed samples were produced by different SLM processing parameters according to Doehlert Matrix. The regression models correlating relative density and three SLM processing parameters (laser power, scan speed, and hatching distance) were built and the optimum parameter combination to get a high relative density was obtained. By plotting the response surfaces and contours of the regression models, it was found that the relative densities are both higher at the combination of the higher scan speed, higher power, and lower hatching distance and at the combination of a lower scan speed, a moderate laser power, and a optional hatching distance. It was also found that the parameter of hatching distance is the crucial parameter to get a high relative density and to get high mechanical property.

Purpose The Ni-based superalloy IN-738 LC is known to be susceptible to porosity and different types of cracking during the build-up process and, thus, challenging to manufacture using selective laser melting (SLM). Determining a feasible set of operating parameters for SLM of nickel-based superalloys involves new approach to experimental design based on the Doehlert method that assists in determining an optimal (feasible) set of operating parameters for SLM of IN-738 LC powder alloy. Design/methodology/approach The SLM parameters are evaluated in terms of their effectiveness in obtaining the microstructure with a porosity content of <0.5 per cent and without micro-cracking. The experimental approach is exemplified with the Doehlert matrix response variable, relative density, by comparing Archimedes method with microstructural assessments of pores and cracks from image analysis. The effect of heat treatment (HT) and hot isostatic pressing (HIP) on the microstructure of the SLMed IN-738 LC powder alloy has been examined and the consequential tensile response characterised. Findings By using optimised process parameters (low heat input, medium scanning speed and small hatching distance) which provides medium energy density, samples of IN-738 LC with a macroscopic porosity <0.5 per cent and free of micro-cracks can be manufactured by SLM. The results indicate that HIP of SLMed material did not lead to a noticeable effect on mechanical properties compared to HT of SLMed material suggesting that the level of both porosity and crack density might be already below the detection limit for the mere heat-treated material. Originality/value SLM processing parameters (power, scan speed, hatching distance) for IN-738 LC were successfully optimised after only 14 experiments using Doehlert design. Two independent methods, Archimedes method and image analysis, were used in this study to assess relative density of SLM-produced samples with sets of processing parameters showing coherency in prediction with predicted response by Doehlert design.

No abstract

Rupture of the scapholunate interosseous ligament can cause the dissociation of scaphoid and lunate bones, resulting in impaired wrist function. Current treatments (e.g., tendon-based surgical reconstruction, screw-based fixation, fusion, or carpectomy) may restore wrist stability, but do not address regeneration of the ruptured ligament, and may result in wrist functional limitations and osteoarthritis. Recently a novel multiphasic bone-ligament-bone scaffold was proposed, which aims to reconstruct the ruptured ligament, and which can be 3D-printed using medical-grade polycaprolactone. This scaffold is composed of a central ligament-scaffold section and features a bone attachment terminal at either end. Since the ligament-scaffold is the primary load bearing structure during physiological wrist motion, its geometry, mechanical properties, and the surgical placement of the scaffold are critical for performance optimisation. This study presents a patient-specific computational biomechanical evaluation of the effect of scaffold length, and positioning of the bone attachment sites. Through segmentation and image processing of medical image data for natural wrist motion, detailed 3D geometries as well as patient-specific physiological wrist motion could be derived. This data formed the input for detailed finite element analysis, enabling computational of scaffold stress and strain distributions, which are key predictors of scaffold structural integrity. The computational analysis demonstrated that longer scaffolds present reduced peak scaffold stresses and a more homogeneous stress state compared to shorter scaffolds. Furthermore, it was found that scaffolds attached at proximal sites experience lower stresses than those attached at distal sites. However, scaffold length, rather than bone terminal location, most strongly influences peak stress. For each scaffold terminal placement configuration, a basic metric was computed indicative of bone fracture risk. This metric was the minimum distance from the bone surface to the internal scaffold bone terminal. Analysis of this minimum bone thickness data confirmed further optimisation of terminal locations is warranted.

No abstract

No abstract

No abstract

No abstract