Laser-induced graphene (LIG) has recently become a point of attraction globally as an environmentally friendly method to fabricate graphene foam in a single step using a CO 2 laser. The electrical properties of LIG are studied in different environmental applications, such as bacterial inactivation, antibiofouling, and pollutant sensing. Furthermore, metal or nonmetal doping of graphene enhances its catalytical performance in pollutant degradation and decontamination. Magneĺi phase (Ti n O 2n−1 ) is a substoichiometric titanium oxide known for its high electrocatalytic behavior and chemical inertness and is being explored as a membrane or electrode material for environmental decontamination. Here, we show the fabrication and characterization of LIG−Magneĺi-phase (Ti 4 O 7 ) titanium suboxide composites as electrodes and filters on poly(ether sulfone). Unlike undoped LIG electrodes, the doped Ti 4 O 7 −LIG electrodes exhibit enhanced electrochemical activity, as demonstrated in electrochemical characterization using cyclic voltammetry and electrochemical impedance spectroscopy. Due to the in situ generation of hydroxyl radicals on the surface, the doped electrodes exhibit increase in methylene blue degradation and microorganism removal. Effects of voltage and doping were examined, resulting in a clear trend of degradation and decontamination performance proportional to the doping concentration and applied voltage giving the best result at 2.5 V for 10% Ti 4 O 7 doping. The LIG−Ti 4 O 7 surfaces also showed biofilm inhibition against mixed bacterial culture. The flowthrough filtration using a LIG−Ti 4 O 7 conductive filter showed complete bacterial killing with 6 log removal in the permeate at 2.5 V, an enhancement of ∼2.5 log compared to undoped LIG filters at a flow rate of ∼500 L m −2 h −1 . The facile fabrication of Ti 4 O 7doped LIG with enhanced electrochemical properties can be effectively used for energy and environmental applications.

No abstract

A healthy environment is necessary for a human being to survive. The contagious COVID-19 virus has disastrously contaminated the environment, leading to direct or indirect transmission. Therefore, the environment demands adequate prevention and control strategies at the beginning of the viral spread. Laser-induced graphene (LIG) is a three-dimensional carbon-based nanomaterial fabricated in a single step on a wide variety of low-cost to high-quality carbonaceous materials without using any additional chemicals potentially used for antiviral, antibacterial, and sensing applications. LIG has extraordinary properties, including high surface area, electrical and thermal conductivity, environmental-friendliness, easy fabrication, and patterning, making it a sustainable material for controlling SARS-CoV-2 or similar pandemic transmission through different sources. LIG’s antiviral, antibacterial, and antibiofouling properties were mainly due to the thermal and electrical properties and texture derived from nanofibers and micropores. This perspective will highlight the conducted research and the future possibilities on LIG for its antimicrobial, antiviral, antibiofouling, and sensing applications. It will also manifest the idea of incorporating this sustainable material into different technologies like air purifiers, antiviral surfaces, wearable sensors, water filters, sludge treatment, and biosensing. It will pave a roadmap to explore this single-step fabrication technique of graphene to deal with pandemics and endemics in the coming future.

Laser-induced graphene (LIG) is a low-cost, chemical-free single-step fabrication process and has shown its potential in water treatment, electronics, and sensing. LIG fabrication optimization is mostly explored for dense polyimide (PI) polymers. However, LIG-based filters and membranes for water treatment need to be porous, and additional steps are required to get porous surfaces from PI-based surfaces. Polyethersulfone (PES) porous membranes are cost-effective and are common in water purification as compared to PI; further, the optimization of LIG fabrication on PES-based porous membranes is not explored. So, this study demonstrated the fabrication, optimization, and characterization of LIG with different laser parameters such as power, speed, image density (ID), focusing, laser platforms, and membrane support layer effect on porous PES commercial (UP010) and lab-casted 15% PES (PES15) membranes. The performance of optimized LIG filters was tested for interfacial evaporation (IE)-based desalination in single and stacked layer configuration and water purification applications such as dye removal and disinfection. IE was done in Joule heating (JH) and solar heating (SH) modes, and the UP010-ID7 LIG filter showed the highest JH evaporation rates of ∼1.1, 1.8, and 2.82 kg m −2 h −1 in single, double, and triple stacked configurations, respectively. Using a JH IE setup, the best-performing UP010-ID7 LIG filters have also shown ∼100% removal of methylene blue dye from the contaminated water. Furthermore, all LIG filters showed a complete 6-log bacterial inhibition at the 5 V filtration experiments; at 2.5 V, the optimized LIG filters showed a higher removal than the non-optimized filters. Additionally, the LIGs obtained with the aluminum platform were the best quality. This work demonstrates that laser power, ID, platform, and membrane support are critical parameters for the best-performing PES-LIG filters, and they can be effectively utilized to fabricate PES-based LIG porous surfaces for various energy, environmental, and catalysis applications.

No abstract