We demonstrate the use of photosensitive epoxy laminate TMMF S2045 for the fabrication and sealing of tapered microfluidic channels. The 45 μm thick resist enables the fabrication of shallow sealed cavities featuring extreme aspect ratios of less than 1:40 (h = 45 μm, w = 2000 μm). It also provides high resolution and enables minimum feature sizes of 10 μm. For the fabrication of free-standing structures, an aspect ratio of up to 7:1 was achieved. The dry-film photoresist can be applied easily by lamination onto structured substrates. The total thickness variation of the resist across a 100 mm wafer was determined to be less than ±0.6 μm. Process parameters for the fabrication and sealing of various micro-channels are discussed and optimized in this paper. The main focus was to minimize thermal impact during lamination, soft-bake, exposure and post-exposure bake, which could lead to lid sagging or channel clogging due to liquefaction of uncured resist. We tested TMMF according to ISO 10995-5 and found it to be non-cytotoxic, enabling its use for biological applications. Swelling of less than 5% for incubation of the dry-film resist in several biologically relevant solvents, buffers and cleaning solutions was observed.

We present a versatile fabrication process for the precise fabrication of embedded three-dimensional microfluidic structures in SU-8 photoresist. The full-wafer bond process based on a polyester (PET) handling layer enhances the previous low-temperature bonding technology. We achieved an extremely high bond strength of 45 MPa while requiring only small anchoring structures. Small channel structures with an aspect ratio >2 as well as wide membranes with an aspect ratio <0.02 were successfully bonded to realize precisely defined channel structures. Furthermore, the developed process features high yields (>80%) and enables the integration of microelectronics. The flexibility of the fabrication process is presented in two contrary applications. A completely freestanding and transparent SU-8 foil with a thickness of 225 µm featuring embedded 3D microchannels was fabricated. Also, high quality ink-jet dispensers were successfully fabricated whereas the dispenser quality mainly depends on the channel quality.

No abstract

We present a new method for the distinct specific chemical stimulation of single cells and small cell clusters within their natural environment. By single-drop release of chemical agents with droplets in size of typical cell diameters (d <30 μm) on-demand micro gradients can be generated for the specific manipulation of single cells. A single channel and a double channel agent release cartridge with integrated fluidic structures and integrated agent reservoirs are shown, tested, and compared in this publication. The single channel setup features a fluidic structure fabricated by anisotropic etching of silicon. To allow for simultaneous release of different agents even though maintaining the same device size, the second type comprises a double channel fluidic structure, fabricated by photolithographic patterning of TMMF. Dispensed droplet volumes are V = 15 pl and V = 10 pl for the silicon and the TMMF based setups, respectively. Utilizing the agent release cartridges, the application in biological assays was demonstrated by hormone-stimulated premature bud formation in Physcomitrella patens and the individual staining of one single L 929 cell within a confluent grown cell culture.

No abstract

No abstract

We present a new tool for the precisely controlled transfer of individual picoliter (pL) droplets in the range of 150-950 pL at user defined local positions within aqueous liquid environments while avoiding any leakage by diffusion. This is achieved by a low-cost, disposable and biocompatible cap that can be placed on top of any pL-dispenser and generates a phase-gap between dispensing agent and target liquid when the dispenser is dipped into the latter. We developed two different working modes: (i) the standard mode enables an instant injection (<< 1 ms) of the droplet into the liquid environment and (ii) the focus mode further increases the spatial resolution from 100 microm to 50 microm at the cost of slowing down the injection time. For the phase-gap we have proven an excellent long-term stability of more than 30 hours against capillary priming.