Developing a surface with low Secondary Electron Yield (SEY) is one of the main ways of mitigating electron cloud and beam-induced electron multipacting in high-energy charged particle accelerators. In our previous publications, a low SEY< 0.9 for as-received metal surfaces modified by a nanosecond pulsed laser was reported. In this paper, the SEY of laser-treated blackened copper has been investigated as a function of different laser irradiation parameters. We explore and study the influence of micro-and nano-structures induced by laser surface treatment in air of copper samples as a function of various laser irradiation parameters such as peak power, laser wavelength ( = 355 nm and 1064 nm), number of pulses per point (scan speed and repetition rate) and fluence, on the SEY. The surface chemical composition was determined by x-ray photoelectron spectroscopy (XPS) which revealed that heating resulted in diffusion of oxygen into the bulk and induced the transformation of CuO to sub-stoichiometric oxide. The surface topography was examined with high resolution scanning electron microscopy (HRSEM) which showed that the laser-treated surfaces are dominated by microstructure grooves and nanostructure features.

Since the installation of an ITER-like wall, the JET programme has focused on the consolidation of ITER design choices and the preparation for ITER operation, with a specific emphasis given to the bulk tungsten melt experiment, which has been crucial for the final decision on the material choice for the day-one tungsten divertor in ITER. Integrated scenarios have been progressed with the re-establishment of long-pulse, high-confinement H-modes by optimizing the magnetic configuration and the use of ICRH to avoid tungsten impurity accumulation. Stationary discharges with detached divertor conditions and small edge localized modes have been demonstrated by nitrogen seeding. The differences in confinement and pedestal behaviour before and after the ITER-like wall installation have been better characterized towards the development of high fusion yield scenarios in DT. Post-mortem analyses of the plasma-facing components have confirmed the previously reported low fuel retention obtained by gas balance and shown that the pattern of deposition within the divertor has changed significantly with respect to the JET carbon wall campaigns due to the absence of thermally activated chemical erosion of beryllium in contrast to carbon. Transport to remote areas is almost absent and two orders of magnitude less material is found in the divertor.

Doppler echocardiographic measurement of time-velocity integral of blood flow across the aortic annulus ("stroke distance") or of stroke volume (SV) have been proposed as noninvasive measures of cardiac pump performance that could elucidate the hemodynamics of hypertension. To evaluate the performance of these measures of hemodynamic volume load in a population with a wide range of body build and other characteristics, we obtained technically adequate imaging and Doppler echocardiograms in 1,935 of 2,212 (87%) American Indian Strong Heart Study participants, without mitral regurgitation or segmental left ventricular (LV) dysfunction, in Arizona, Oklahoma, and South/North Dakota. The subjects ranged widely in age (48 to 81 years) and body mass index (17.0 to 62.6 kg/m2); 65% were women; 1,161 were normotensive and 774 were hypertensive. As a reference standard, LV and stroke volumes were calculated from LV internal dimensions by the Teichholz method. Doppler SVs were moderately related to LV SVs (r = 0.63), but Doppler SV was slightly lower in both normotensive (mean = 69.8 and 72.9 mL, respectively) and hypertensive subjects (71.1 v 73.6 mL). Aortic stroke distance was less closely related than was aortic annular area to LV SV (r = 0.34 v 0.40, P < .001). Aortic annular area (r = 0.44) but not stroke distance (r = 0.04) was moderately correlated with body surface area. Stroke distance was inversely related to annular area (r = -0.29) and in subjects stratified by aortic annular diameter 1.6 to 1.9, 2.0 to 2.1, and 2.3 to 2.9 cm, mean LV SV increased from 67 to 74 to 80 mL, but average stroke distance fell from 22.8 to 21.6 to 20.1 cm. Stroke distance also failed to identify gender differences in LV SV but did identify that due to obesity. Thus Doppler SV closely parallels independently measured LV SV but slightly underestimates SV in both normotensive and hypertensive adults, whereas aortic stroke distance yields misleading comparisons between genders or individuals of different body sizes.

EDFA, as part of the Power Plant Physics and Technology programme, has been working on the preconceptual design of a Demonstration Power Plant (DEMO). As part of this programme, a review of the remote maintenance strategy considered maintenance solutions compatible with expected environmental conditions, whilst showing potential for meeting the plant availability targets. A key finding was that, for practical purposes, the expected radiation levels prohibit the use of complex remote handling operations to replace the first wall. In 2012/13, these remote maintenance activities were further extended, providing an insight into the requirements, constraints and challenges. In particular, the assessment of blanket and divertor maintenance, in light of the expected radiation conditions and availability, has elaborated the need for a very different approach from that of ITER. This activity has produced some very informative virtual reality simulations of the blanket segments and pipe removal that are exceptionally valuable in communicating the complexity and scale of the required operations. Through these simulations, estimates of the maintenance task durations have been possible demonstrating that a full replacement of the blankets within 6 months could be achieved. The design of the first wall, including the need to use sacrificial limiters must still be investigated. In support of the maintenance operations, a first indication of the requirements of an Active Maintenance Facility (AMF) has been elaborated.