This study inspects the viability of engaging the discarded paper wastes in concrete by varying the volume proportions from 0%–20% with each 5% increment in replacement of the weight of cement. A physiomechanical study was conducted, and the results were presented. A glass fiber reinforced rectangular slab with a longer span (ly) to shorter span (lx) ratio of (ly: lx) 1.16 was cast with optimum replacement of waste-paper mass and compared the force-deformation characteristics with the conventional concrete slab without waste paper. The optimum percentage of discarded papers for the replacement of cement is 5%. Also, the results imply that the compressive strength at the age of 28 days is 30% improved for the optimum replacement. Based on the outcomes of the investigation, it can be inferred that the compressive strength gets progressively reduced if the volume of the discarded paper gets increases. The incorporation of glass fibers improves the split and flexural strength of the concrete specimens considerably. The ultimate load-carrying capacity of the glass fiber reinforced waste paper incorporated concrete slab measured 42% lower than that of the conventional slab. However, development of the new type of concrete incorporating waste papers is the new trend in ensuring the sustainability of construction materials.

Infilled wall is a primary structure which is used in a multistorey RC-framed structure. It is not designed like structural elements, but it is subjected to structural load and response as a heavily damaged element into the building. The main problem of an infilled wall is not actively utilizing in the framed structure and it is not interacted with frame elements. The objective of research is to utilize the infilled wall in the RC-framed structure by improving its performance of behavior. Here, two different types of brick masonry like Autoclaved concrete and clay brick masonry were used as the infilled wall in an RC-framed structure. A singly bay and single storey RC framed structure was cast and tested under a 1/10th scale model by diagonal compressive loading. The specimen was subjected to static loading by a universal testing machine. Infilled wall is weak in tension, so a reinforcing band was used to improve the performance like load carrying capacity, stiffness, ductility, and energy dissipation capacity. Based on the results of the experimental study, it is found that reinforcing band with the infilled wall gives better behavior of the RC-framed structure.

Laced Reinforced Concrete (LRC) structural elements are generally used in the defence environments where the structure encounters blast/impulsive loading. It comprises of equal number of reinforcements in both the faces of the beam with lacings as shear reinforcements bent at 450 along the plane of principal bending and fastened in position by cross rod. This paper presents the performance of LRC beam by experimental investigation and compared with conventional Reinforced Concrete (RC) beam using four point flexural load testing. Experimental results indicate that the LRC beam perform well than the RC beam considering the deformation. Failure modes could not be ascertained, since the experiments were stopped due to limitations in test set-up. At this stage, the support rotation achieved by LRC beam and RC beam is found to be 4.70 and 2.430 respectively. The LRC beam is found to be more ductile than RC beam. The structural response of LRC beam and RC beam is compared and presented.

The current study aimed to analyse the viability of incorporating the post cryogenic discarded rubber and the air-cooled slag as an aggregate in partial replacement of stone dust in fly ash bricks production. A range of mechanical, non-destructive, and microstructural tests was performed on bricks thus produced by incorporating rubber and slag aggregates in various dosages (i.e., 5, 10, 15, 20 and 25% by stone dust weight). The result revealed that the compressive strength dropped from 71 to 43 % in the case of rubber aggregate replacement. Morphology study confirms that the rubber aggregates resulted in the porous microstructure of the bricks and leads to lesser unit weight and lighter structure. The rubber may be used as a lightweight aggregate in the brick possibly as it reduces the density of the final product. However, the use of rubber in bricks needs to be cautiously designed to get hold of productive solutions at the end. The findings demonstrate that the copper slag substitution of up to 15%, found to be enhanced the strength properties and it will be a better choice for low-cost construction as a promising alternative construction material.

No abstract