A theoretical study investigating the effects of both anisotropic and isotropic surface roughness on the convective stability of the boundary-layer flow over a rotating disk is described. Surface roughness is modelled using a partial-slip approach, which yields steady-flow profiles for the relevant velocity components of the boundary-layer flow which are a departure from the classic von Kármán solution for a smooth disk. These are then subjected to a linear stability analysis to reveal how roughness affects the stability characteristics of the inviscid Type I (or cross-flow) instability and the viscous Type II instability that arise in the rotating disk boundary layer. Stationary modes are studied and both anisotropic (concentric grooves and radial grooves) and isotropic (general) roughness are shown to have a stabilizing effect on the Type I instability. For the viscous Type II instability, it was found that a disk with concentric grooves has a strongly destabilizing effect, whereas a disk with radial grooves or general isotropic roughness has a stabilizing effect on this mode. In order to extract possible underlying physical mechanisms behind the effects of roughness, and in order to reconfirm the results of the linear stability analysis, an integral energy equation for three-dimensional disturbances to the undisturbed three-dimensional boundary-layer flow is used. For anisotropic roughness, the stabilizing effect on the Type I mode is brought about by reductions in energy production in the boundary layer, whilst the destabilizing effect of concentric grooves on the Type II mode results from a reduction in energy dissipation. For isotropic roughness, both modes are stabilized by combinations of reduced energy production and increased dissipation.
We summarise results of a theoretical study investigating the distinct convective instability properties of steady boundary-layer flow over rough rotating disks. A generic roughness pattern of concentric circles with sinusoidal surface undulations in the radial direction is considered. The goal is to compare predictions obtained by means of two alternative, and fundamentally different, modelling approaches for surface roughness for the first time. The motivating rationale being to identify commonalities and isolate results that might potentially represent artefacts associated with the particular methodologies underlying one of the two modelling approaches.The most significant result of practical relevance obtained is that both approaches predict overall stabilising effects on the Type I instability mode of rotating disk flow. This mode leads to transition of the rotating-disk boundary layer and, more generally, the transition of boundary-layers with a cross-flow profile. Stabilisation of the Type 1 mode means that it may be possible to exploit surface roughness for laminar-flow control in boundary layers with a cross-flow component. However, we also find differences between the two sets of model predictions, some subtle and some substantial. These will represent criteria for establishing which of the two alternative approaches is more suitable to correctly describe experimental data when these become available.
Results of a computational study are discussed which investigate roughness-induced and geometryinduced (confinement) effects on the steady-state velocity components in 3-D boundary-layer flow over the rotor disc in a rotor-stator flow configuration. It is found that, for the rotor-stator flow investigated, the roughness-induced effects are very similar to geometry-induced effects, both in nature and magnitude. The overall aim was to compare these two types of effects with corresponding roughness-induced effects in the von Kármán boundary-layer flow over a disc spinning freely in an unrestricted fluid environment. The research was conducted in the context of a programme investigating surface roughness as a means of laminar flow control for the development of new passive drag-reduction techniques. The goal was to establish whether it was possible unequivocally to distinguish between roughness-induced and geometry-induced effects on the boundary-layer flow above the rotor disc. The results obtained suggest that, for the type of system discussed here, it must be expected to be difficult to distinguish between these effects in experiments. The similarities regarding the nature and magnitude of results obtained from comparing predictions for three different computational modelling approaches indicate the required sensitivity of measurement technologies aiming to resolve the investigated effects in experimental studies.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.