This paper presents vibration analysis and structural optimization of a swimming–morphing structure. The swimming of the structure is achieved by utilization of piezoelectric patches to generate traveling waves. The third mode shape of the structure in the longitudinal direction resembles the body waveform of a swimming eel. After swimming to its destination, the morphing structure changes shape from an open box to a cube using shape memory alloys (SMAs). The SMAs used for the configuration change of the box robot cannot be used for swimming since they fail to operate at high frequencies. Piezoelectric patches are actuated at the third natural frequency of the structure. We optimize the thickness of the panels and the stiffness of the springs at the joints to generate swimming waveforms that most closely resemble the body waveform of an eel. The traveling wave is generated using two piezoelectric sets of patches bonded to the first and last segments of the beams in the longitudinal direction. Excitation of the piezoelectric results in coupled system dynamics equations that can be translated into the generation of waves. Theoretical analysis based on the distributed parameter model is conducted in this paper. A scalar measure of the traveling to standing wave ratio is introduced using a 2-dimensional Fourier transform (2D-FFT) of the body deformation waveform. An optimization algorithm based on tuning the flexural transverse wave is established to obtain a higher traveling to standing wave ratio. The results are then compared to common methods in the literature for assessment of standing to traveling wave ratios. The analytical models are verified by the close agreement between the traveling waves predicted by the model and those measured in the experiments.

The main drawback of energy harvesting using the piezoelectric direct effect is that the maximum electric power is generated at the fundamental resonance frequency. This can clearly be observed in the size and dimensions of the components of any particular energy harvester. In this paper, we are investigating a new proposed energy harvesting device that employs the Automatic Resonance Tuning (ART) technique to enhance the energy harvesting mechanism. The proposed harvester is composed of a cantilever beam and sliding masse with varying locations. ART automatically adjusts the energy harvester’s natural frequency according to the ambient vibration natural frequency. The ART energy harvester modifies the natural frequency of the harvester using the motion of the mobile (sliding) mass. An analytical model of the proposed model is presented. The investigation is conducted using the Finite Element Method (FEM). THE FEM COMSOL model is successfully validated using previously published experimental results. The results of the FEM were compared with the experimental and analytical results. The validated model is then used to demonstrate the displacement profile, the output voltage response, and the natural frequency for the harvester at different mass positions. The bandwidth of the ART harvester (17 Hz) is found to be 1130% larger compared to the fixed resonance energy harvester. It is observed that the proposed broadband design provides a high-power density of 0.05 mW mm−3. The piezoelectric dimensions and load resistance are also optimized to maximize the output voltage output power.

No abstract

This work presents a model for energy harvesting characterization of a simply supported beam with a mass in the middle to be used for powering pacemakers from heartbeat vibrations. The required power for a typical pacemaker is about 1.0 microwatts. A uniform cross-section beam, bimorph structures, employing double piezoelectric layers is used. PSI-5H4E piezoelectric and brass substrate is used in this study. Different configurations are utilized to identify the optimal design for lightweight energy harvesting devices with low-power applications to tune the natural frequencies of the energy harvester towards the operating ambient vibration source. In this paper, the exact analytical solution of the piezoelectric beam energy harvester with Euler–Bernoulli beam assumptions is presented. The energy harvester is intended to generate power from heartbeat induced vibrations to power implantable cardiac devices. The base excitations are thus heartbeat induced tissue vibrations. The proposed configuration harvests energy from the reverberation of heartbeats and converts it to electricity and could generate about 0.22 microwatts of power. Using the Fourier transform, the frequency response function for the voltage; current and power of the harvester are obtained. The power output for a range of values for the resistive load connected to the bimorph PZT layers is investigated to determine the optimized value of the resistive load that gives the maximum power output for the corresponding configuration of the beam. Stress analysis is performed for the substrate and PZT layer to make sure that the stress are within the permissible values to avoid breaking or failing of the beam. Results show that the use of mid mass is capable of harvesting a significant power with the proposed configurations.

No abstract

In this paper, rainfall droplet impact force is transformed into a measurable voltage signal output via the piezoelectric material direct effect utilized for sensing purposes. The motivating sensor is utilized to measure the peak impact forces of rainfall droplets for further analysis and processing. Constructing a sense for the impact force of rainfall droplets has great implications in many real-life applications that can provide vital information regarding the amplifications of the impact force of rainfall on soil erosion, and the impact on small creatures and plants, etc. The rainfall droplet is set to collide on a very thin aluminum plate with negligible mass that can be presented geometrically as an extended segment of the proposed sensing device. The proposed sensing device is composed of a bimorph simply supported composite-piezoelectric beam that buckles due to the effect of the rain droplets’ vertical impact force. The proposed device is designed for optimal performance in terms of the amount of voltage that can be measured. This is accomplished by having the first critical buckling load of the device as less than the impact force of the rainfall droplet. Accordingly, the well-known genetic algorithm (GA) automated optimization technique is utilized in this paper to enhance the measured voltage signal. A proof mass is added to the middle of the beam to amplify the magnitude of the measured voltage signal. The voltage signal is intended to be transferred to the PC via a data acquisition system. The rainfall droplets’ peak impact forces are obtained analytically due to the nonlinear behavior of the beam using the Euler–Bernoulli thin beams assumptions. The FE model using COMSOL 6.0 Multiphysics commercial software is used to verify the analytical results.

This paper presents vibration analysis and structural optimization of a self-assembled structure for swimming. The third mode shape of the structure in the longitudinal direction resembles the body waveform of a swimming eel fish. At the final destination, the box self-assembles using shape memory alloys. MFCs (Piezoelectric Micro Fiber Composites) are actuated at the fundamental natural frequency of the structure. This excites the primary mode of resonance. We optimize the thickness of the panels and the stiffness of the joints to most efficiently generate the swimming waveforms that resembles the body waveform of eel. Traveling wave is generated using two piezoelectric batches actuators bonded on the first and fourth segments of the beams in the longitudinal direction. Excitation of the piezoelectrics results in coupled system dynamics equations that can be translated into generation of waves. Theoretical analysis based on the distributed parameter model was conducted in this paper. A scalar measure of the traveling to standing wave ratio was created using 2-dimensional Fourier Transform of the wave form. The results then were compared to common method in the literature for assessment of standing to traveling wave ratio.

In this paper, a new prototype is proposed for accelerated orthodontic tooth treatment. In contrast to conventional methods, where heavy vibration generators are used, the proposed design is light and small and may remain into patient’s mouth without obstructing his daily activities. To do that, a PVDF Piezoelectric actuator layer is incorporated into a bio-compatible flexible structure which is to be excited by an external electric source. Generally, application of cyclic loading (vibration) reverses bone loss, stimulates bone mass, induces cranial growth, and accelerates tooth movement. This reduce the pain experience and discomfort associated with the treatment and also enhances the patient compliance with the treatment. Vibration has the advantage of minimal side effects in comparison to medicinal treatments. This configuration enables the operator to adjust the vibration frequency as well as the orthodontic force exerted on the tooth.