Electrochemical capacitors, also known as supercapacitors, are becoming increasingly important components in energy storage, although their widespread use has not been attained due to a high cost/ performance ratio. Fundamental research is contributing to lowered costs through the engineering of new materials. Currently the most viable materials used in electrochemical capacitors are biomass-derived and polymer-derived activated carbons, although other carbon materials are useful research tools. Metal oxides could result in a step change for electrochemical capacitor technology and is an exciting area of research. The selection of an appropriate electrolyte and electrode structure is fundamental in determining device performance. Although there are still many uncertainties in understanding the underlying mechanisms involved in electrochemical capacitors, genuine progress continues to be made. It is argued that a large, collaborative international research programme is necessary to fully develop the potential of electrochemical capacitors

b s t r a c tPorous carbon aerogels are prepared by polycondensation of resorcinol and formaldehyde catalyzed by sodium carbonate followed by carbonization of the resultant aerogels in an inert atmosphere. Pore structure of carbon aerogels is adjusted by changing the molar ratio of resorcinol to catalyst during gel preparation and also pyrolysis under Ar and activation under CO 2 atmosphere at different temperatures.The prepared carbons are used as active materials in fabrication of composite carbon electrodes. The electrochemical performance of the electrodes has been tested in a Li/O 2 cell. Through the galvanostatic charge/discharge measurements, it is found that the cell performance (i.e. discharge capacity and discharge voltage) depends on the morphology of carbon and a combined effect of pore volume, pore size and surface area of carbon affects the storage capacity. A Li/O 2 cell using the carbon with the largest pore volume (2.195 cm 3 /g) and a wide pore size (14.23 nm) showed a specific capacity of 1290 mA h g −1 .

No abstract

The use of ionic liquid (IL) electrolytes promises to improve the energy density of electrochemical capacitors (ECs) by allowing for operation at higher voltages. Several studies have also shown that the pore size distribution of materials used to produce electrodes is an important factor in determining EC performance. In this research the capacitative, energy and power performance of ILs 1-ethyl-3-methylimidazolium tetrafluoroborate (EMImBF(4)), 1-ethyl-3-methylimidazolium dicyanamide (EMImN(CN)(2)), 1,2-dimethyl-3-propylimidazolium bis(trifluoromethylsulfonyl)imide (DMPImTFSI), and 1-butyl-3-methylpyrrolidinium tris(pentafluoroethyl)trifluorophosphate (BMPyT(F5Et)PF3) were studied and compared with the commercially utilised organic electrolyte 1M tetraethylammonium tetrafluoroborate solution in anhydrous propylene carbonate (Et4NBF4-PC 1 M). To assess the effect of pore size on IL performance, controlled porosity carbons were produced from phenolic resins activated in CO2. The carbon samples were characterised by nitrogen adsorption-desorption at 77 K and the relevant electrochemical behaviour was characterised by cyclic voltammetry, galvanostatic charge-discharge and electrochemical impedance spectroscopy. The best capacitance performance was obtained for the activated carbon xerogel with average pore diameter 3.5 nm, whereas the optimum rate performance was obtained for the activated carbon xerogel with average pore diameter 6 nm. When combined in an EC with IL electrolyte EMImBF(4) a specific capacitance of 210 F g(-1) was obtained for activated carbon sample with average pore diameter 3.5 nm at an operating voltage of 3 V. The activated carbon sample with average pore diameter 6 nm allowed for maximum capacitance retention of approximately 70% at 64 mA cm(-2)

The use of Room Temperature Ionic Liquid (RTIL) electrolytes promises to improve the energy density of Electrochemical Capacitors (ECs) by allowing for operation at higher voltages. RTIL electrolytes 1-ethyl-3-methylimidazolium tetrafluoroborate (EMImBF(4)), 1-ethyl-3-methylimidazolium dicyanamide (EMImN(CN)(2)), 1,2-dimethyl-3-propylimidazolium bis(trifluoromethylsulfonyl)imide (DMPImTFSI), and 1-butyl-3-methylpyrrolidinium tris(pentafluoroethyl)trifluorophosphate (BMPyFAP) were studied. Tetraethylammonium tetrafluoroborate 1 molar solution in anhydrous propylene carbonate (Et(4)NBF(4)-PC 1M) was studied for comparison purposes. Carbon was produced from phenolic resin activated in CO(2). The porosity of the carbon samples were characterised by N(2) adsorption-desorption at 77 K and the relevant electrochemical behaviour was characterised by galvanostatic charge-discharge, electrochemical impedance spectroscopy and cyclic voltammetry. The highest operating voltage of 3.5 V was obtained for BMPyFAP, whilst the best capacitive performance was obtained for EMImBF(4). The maximum energy density increased to 70 Wh kg(-1) (carbon) for RTIL EMImBF(4) from 35 Wh kg(-1)(carbon) for the organic electrolyte Et(4)NBF(4)-PC 1M. It was found that the performance of the RTIL electrolytes could be related to the IL viscosity and ion size whilst the electrolyte equivalent series resistances produced a linear relationship with viscosity. It was found that the capacitance performance of the RTIL electrolytes followed the order EMImBF(4) > DMPImTFSI > BMPyFAP > EMImN(CN)(2). The electrolyte and equivalent series resistance were in the order EMImN(CN)(2) < EMImBF(4) < DMPImTFSI < BMPyFAP.