A new chelating resin was prepared by coupling Amberlite XAD-4 with alizarin red-s through an azo spacer, characterized by infra-red spectroscopy and thermal analysis and studied for Rh(III) preconcentration using inductively coupled plasma atomic emission spectroscopy (ICP-AES) for rhodium monitoring in the environment. The optimum pH for sorption of the metal ion was 6.5. The sorption capacity was found 2.1 mg/g of resin for Rh(III). A recovery of 88% was obtained for the metal ion with 1.5 M HCl as eluting agent. Kinetic adsorption data were analyzed by adsorption and desorption times of Rh(III) on modified resin. Scat chard analysis revealed that the homogeneous binding sites were formed in the polymers. The linear regression equation was Q/C = –1.3169Q + 27.222 (R2 = 0.9239), for Rh were formed in the SPE sorbent,Kd and Qmax for the affinity binding sites were calculated to be 0.76 μmol/mL and 20.67 μmol/g, respectively. The equilibrium data and parameters of Rh(III) adsorption on modified resin were analyzed by Langmuir, Freundlich, Temkin and Redlich–Peterson models. The experimental adsorption isotherm was in good concordance with Langmuir and Freundlich models (R2 > 0.998) and based on the Langmuir isotherm the maximum amount of adsorption (qmax) was 4.842 mg/g. The method was applied for rhodium ions determination in environmental samples. with high recovery (>80%).

In this study, the imprinted aniline-formaldehyde was used as an adsorbent for removal of Iridium and Palladium ions from aqueous solutions through batch equilibrium. The sorbent was characterized by fourier transform infrared spectroscopy. The influence of pH, equilibrium time, temperature and initial concentration of metal ions on adsorbed amount of both ions were investigated. The maximum adsorption capacity in initial concentration of 100 mg/L was found to be 12.5 mg/g at pH 7.0 and 14.3 mg/g at pH 8.0 for Iridium and Palladium, respectively. In addition, the best desorption of the metal ions from resin was obtained by 0.5 mol/L nitric acid as eluting agent. The profile of both ions uptake on this sorbent reflects good accessibility of the chelating sites in the imprinted aniline-formaldehyde. Langmuir, Freundlich, Temkin and Redlich-Peterson isotherm models were applied to analyze the experimental data. Moreover, Langmuir linear method was used to obtain the isotherm parameters. However, Langmuir type II achieved the highest coefficient which led to the best fit for the palladium and the best fit for Iridium obtained from linear Redlich-Peterson. However, the thermodynamic parameters (DG°, DH°, and DS°) were also determined using the equilibrium constant values obtained at different temperatures. The results showed that the adsorption for Iridium and Palladium ions was spontaneous nature and endothermic. Moreover, the method was applied for the determination of both ions from tap water samples.

No abstract

Investigations were carried out to compare the effectiveness of compounds such as sodium nitrite, trisodium citrate (TSC) and TSC-zinc acetate to inhibit the corrosion of steel rebar in simulated concrete interstitial solution contaminated with chloride and to explain the mechanism of corrosion inhibition on reinforcing steel by these systems. Inhibition efficiency of these systems was studied by electrochemical techniques such as potentiodynamic polarization and half cell potential measurements. Electronic spectral studies of simulated pore solution and FT-IR spectral investigations of the film deposited on steel surface were carried out for understanding the mechanism of corrosion inhibition. Microscopic surface analysis was conducted to obtain the surface morphological behaviour of steel rebar. TSC alone was not exhibited good corrosion inhibition at very low and high concentrations according to electrochemical studies. However, in the presence of zinc acetate, corrosion protection efficiency of TSC increased appreciably. When comparing with sodium nitrite, TSC in the presence and absence of zinc acetate displayed good corrosion inhibition efficiency. Among a number of samples, TSC 100 ppm-zinc acetate 50 ppm combination showed maximum corrosion inhibition efficiency on steel rebar in simulated concrete interstitial solution.