Experimental investigation into the effects of two-stage injection on fuel injection quantity, combustion and emissions in a high-speed optical common rail diesel engine
The present work introduces a new technology for converting energy from steps into electricity. It starts with a study of the mechanical energy available from steps in a busy corridor. The subsequent development efforts and devices are presented, with an iterative approach to prototyping. Methods for enhancing the piezoelectric conversion efficiency have been determined as a part of the process and are introduced in the present article. Capitalizing on these findings, we have fabricated energy‐harvesting devices for stairs that power embedded emergency lighting. The typical working unit comprises an energy‐harvesting stair nosing, a power management circuit, and an embedded light‐emitting diode that lights the tread in front of the user with an illuminance corresponding to emergency standards. The stair nosing generates up to 17.7 mJ of useful electrical energy per activation to provide up to 10.6 seconds of light. The corresponding energy density is 0.49 J per meter square and per step, with an 8.5 mm thick active layer.
The latest generation of high-pressure common rail equipment now provides diesel engines possibility to apply as many as eight separate injection pulses within the engine cycle for reducing emissions and for smoothing combustion. With these complicated injection arrangements, optimizations of operating parameters for various driving conditions are considerably difficult, particularly when integrating fuel injection parameters with other operating parameters such as exhaust gas recirculation rate and boost pressure together for evaluating calibration results. Understanding the detailed effects of fuel injection parameters upon combustion characteristics and emission formation is therefore particularly critical. In this article, the results and discussion of experimental investigations on a high-speed direct injection light-duty diesel engine test bed are presented for evaluating and analyzing the effects of main adjustable parameters of the fuel injection system on all regulated emission gases and torque performance. Main injection timing, rail pressure, pilot amount, and particularly pilot timing have been examined. The results show that optimization of each of those adjustable parameters is beneficial for emission reduction and torque improvement under different operating conditions. By exploring the variation in the interval between the pilot injection and the main injection, it is found that the pressure wave in the common rail has a significant influence on the subsequent injection. This suggests that special attentions must be paid for adjusting pilot timing or any injection interval when multi-injection is used. With analyzing the fuel amount oscillation of the subsequent injections to pilot separation, it demonstrates that the frequency of regular oscillations of the actual fuel amount or the injection pulse width with the variation in pilot separation is always the same for a specified fuel injection system, regardless of engine speed, fuel amount, injection pulse, and injection pressure.
The final, definitive version of this paper has been published in International Journal of Engine Research, Vol 15 Issue 1, September 2012, ppublished by SAGE Publishing, All rights reserved.In order to meet the ever more stringent emission standards, significant efforts have been devoted to the research and development of internal combustion engines. The requirements for more efficient and responsive diesel engines have led to the introduction and implementation of multiple injection strategies. However, the effects of such injection modes on the hydraulic systems, such as the high-pressure pipes and fuel injectors, must be thoroughly examined and compensated for since the combustion and the formation of pollutants in direct-injection engines are directly influenced by the spatial and temporal distribution of the injected fuel within the combustion chamber. This study investigated the hydraulic effects of two-stage fuel injection on diesel combustion and emissions. The fuel-injection system was characterised for all the tested strategies through the measurement of the fuel-injection rate and quantity. In particular, the interaction between the two injection events was identified. The effects of two-stage injection, dwell angle and the interactions between two consecutive injection events on the combustion process and the emissions were investigated in a high-speed direct-injection single-cylinder optical diesel engine using heat-release analysis and high-speed fuel spray and combustion visualisation techniques. The results indicated that the two-stage injection strategy has the potential for simultaneous reduction of nitrogen oxide, soot and unburned hydrocarbon emissions. The results suggested that an optimum fuel quantity in the first injection exists, 0???30%, with which simultaneous reduction of nitrogen oxide, soot and unburned hydrocarbon emissions can be achieved with the added benefits of improved engine performance, fuel economy and combustion noise. However, higher soot emissions were produced, mainly due to the interaction between the two consecutive fuel-injection events whereby the fuel sprays during the second injection were injected into burning regions, as well as reduced soot oxidation due to the continuation of the combustion into the expansion stroke
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.