Hydraulic fracturing has proven to be extremely successful in the western desert of Egypt. Approximately 85% of production in this area results from this stimulation technique, specifically in the reservoirs of interest documented in this paper. However, a deterrent to fracturing in many cases has been the proximity of the producing zones to underlying (or overlying) water zones, either located near the water-oil contact or hydrocarbon zones adjacent to water-bearing zones. In the absence of geological barriers, the fracture height can grow uncontrolled during a fracturing treatment into the water-bearing interval and cause unwanted water production. Excessive water production threatens the economics of a well by: shortening its production life, increasing disposal and lifting costs, boosting the fines migration, and increasing the rate of tubular corrosion and scale buildup. Many times, in marginal fields, these can be sufficient reasons to consider not fracturing. This paper presents case histories where wells were hydraulically fractured using conventional techniques resulting in higher than 60% water cut (even as much as 100% in one case); while with the use of the conformance-while-fracturing (CWF) method, the water cut obtained was as low as 4%, even when the adjacent water zones were within 20 ft of the perforations. This technique provides a tremendous boost to the economics and an effective solution (increasing recoverable reserves from these wells by allowing the hydrocarbons to be produced almost water-free) to a field otherwise plagued with water production. The CWF technique incorporates a relative-permeability modifier (RPM) in the fracturing-fluids design. The RPM provides a reduction in effective permeability to water without significant changes to the relative permeability to oil. This paper discusses the geological and reservoir parameters of the wells and zones of interest, the properties of the RPM, the CWF job-design considerations (and the associated challenges to the job design), its field applications, and post-fracturing results in comparison to offset wells fractured conventionally in the same reservoir and at the same level. It is envisaged that CWF techniques will prove to be beneficial to other operators faced with similar production challenges.
Enhancing hydrocarbon recovery is the ultimate goal in the oil and gas business; nowadays there are many technologies that can be applied effectively to reach that goal; Maximum reservoir contact (MRC) wells, Under-balanced drilling (UBD), Multi-laterals (ML), fishbone. etc. However, still the preferable, economical option is to improve the well production by stimulation which is applied easily and riglessly in existing or newly drilled wells. In many horizontal or long pay zone wells; the optimum results cannot be achieved through conventional stimulation techniques because it is difficult to ensure even stimulation fluid distribution (i.e. acid in the case of carbonate stimulation) across the entire lateral hole unless some sort of selective stimulation can be performed. This is a prerequisite for successful result. It becomes more challenging in heterogeneous open hole completions which have natural fractures. Even more challenging is trying to achieve selective stimulation in such complex geological environment when specific reservoir compartments need to be treated specifically. A tight gas carbonate reservoir with no oil rim in a super-giant onshore gas field in Abu Dhabi was particularly targeted for stimulation during a field review to increase field production. Conventional stimulation treatments performed to restore well productivity resulted in rapid performance decline as a result of undesired worm-holing throughout the existing bore hole and uneven flow contributions. PLTs’ were run in three wells to understand the well productivity. The results showed that most of the gas production (approximately 95%) was from upper zones while the remaining production came from the lower zones which were of poor reservoir quality. It became necessary to look at selective fracturing stimulation techniques that could be applied riglessly and allow contribution from the non-producing zones. This paper describes a unique engineering approach, the Hydrajet Fracturing (HJF) technique that was successfully executed for this purpose. The objective was to apply an economically feasible, rigless, selective fracturing technique with efficient placement approach that would lead to proper reservoir drainage. Pin-point stimulation at selected points was considered an important factor for the development of this field. After the unique stimulation treatment, a new technology based on spectral noise logging and temperature distribution survey was used to evaluate the contribution of the targeted fractured zones in conjunction with pressure buildup well test analysis. Several lessons were learnt from the first use of this technology and some interesting conclusions were reached from these investigations.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.