Crown ether is a form of ethylene oxide cyclo-oligomer. Crown ether has a strong ability to form a complex with cations. The crown ether has been used as part of the electrochemical sensor and optical sensor because of its selectivity to several cations. There was no report on the use of the 18-crown-6-ether as a single coating layer on the QCM sensor. This work investigates the loading effect of the 18-crown-6-ether as a selective coating for QCM sensors as a pre-requirement for a selective coating layer. The impedance spectrum of the QCM sensor coated with 18-crown-6-ether at different concentrations solved in three different solvents was measured. The effects of solvents and 18-crown-6-ether concentrations to the calculated thickness and the effect of the QCM sensor impedance was investigated. The solvents used are Toluene, Tetrahydrofuran (THF), and Chloroform. The results show that the film behaves like a rubber material, which is shown by the impedance value of the sensor at the series resonance frequency. It can be concluded that the thickness of the 18-crown-6-ether layer must be maintained less than one μm to avoid damping on the QCM sensor.
Penggunaan plasma untuk "mengaktifkan" prekursor uap kimia (Plasma Chemical Vapor Deposition (CVD)) memungkinkan proses deposisi berlangsung pada suhu yang lebih rendah daripada proses deposisi menggunakan teknik CVD konvensional. Sistem plasma CVD telah dirancang untuk deposisi lapisan karbon di atas substrat kaca. Bagian utama dari reaktor plasma CVD ini meliputi tutup reaktor, chamber reaktor dan konfigurasi elektroda Capacitively Coupled Discharge (CCD). Chamber reaktor dibuat dari desikator, sementara elektroda dibuat dari stainless steel tipe SS 304. Tingkat vakum pada sistem ini adalah medium vakum (3,090295 Torr). Heater Catridge digunakan sebagai pemanas elektroda bagian bawah (meja sampel). Gas yang digunakan terdiri dari gas Argon sebagai carrier gas, Blue Gaz sebagai sumber karbon yang akan dideposisikan. Parameter reaktor yang dapat dikontrol adalah laju aliran gas. Perbandingan laju alir gas Argon: Blue Gaz optimal yang digunakan adalah (25: 24,2) mL/min .Plasma yang dihasilkan dari sistem ini adalah plasma glow discharge.
Polistiren(Ps) merupakan bahan polimer yang banyak digunakan untuk aplikasi sensor karena sifat viskoelastiknya. Permukaan lapisan Ps yang bersifat hidrofilik sangat diperlukan dalam aplikasi sensor untuk cairan. Permukaan yang bersifat hidrofilik dapat diperoleh dengan memodifikasi permukaan lapisan Ps menggunakan paparan sinar UV. Pada penelitian ini, waktu penyinaran UV yang digunakan adalah selama 30 menit, 60 menit, 90 menit, dan 120 menit. Variasi waktu penyinaran UV bertujuan untuk mengetahui perubahan sifat permukaan Ps. Hidrofilisitas polimer terkait dengan berat molekul dan polaritas polimer. Hal ini dapat dianalisis dengan menggunakan karakterisasi nilai sudut kontak lapisan Ps. Karakterisasi lapisan Ps setelah dipapari sinar UV dilakukan dengan menganalisis perubahan nilai sudut kontak. Berdasarkan percobaan yang telah dilakukan didapatkan bahwa semakin lama penyinaran UV menyebabkan semakin rendahnya nilai sudut kontak lapisan Ps. Nilai sudut kontak paling rendah yang dihasilkan adalah sebesar 55,801o ±0,0563o setelah dipapari sinar UV selama 120 menit.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.