No abstract

Immobilization of submonolayers to 4-5 multilayers of organic molecules on carbon surfaces can be performed by in situ generation of aryl radicals from aryltriazenes. The central idea consists of oxidatively forming an electrogenerated acid of N,N'-diphenylhydrazine to convert the aryltriazene to the corresponding diazonium salt in the diffusion layer of the electrode. In a second step, the diazonium salt is reduced at the same electrode to give a surface of covalently attached aryl groups. In this manner, various moieties tethered to the aryl groups can be immobilized on the surface. Here a ferrocenyl group was introduced as redox marker, the electrochemical signal of which is extraordinarily well-defined. This behavior is independent of film thickness, the latter being easily controlled by the number of repetitive cycles performed. It is also demonstrated that the new approach is suitable for patterning of surfaces using scanning electrochemical microscopy.

Electrografting using aryldiazonium salts provides a fast and efficient technique to functionalize commercially available 3-5 layered graphene (vapour-deposited) on nickel. In this study, Raman spectroscopy is used to quantify the grafting efficiency of cyclic voltammetry which is one of the most versatile, yet simple, electrochemical techniques available. To a large extent the number of defects/substituents introduced to the basal plane of high-quality graphene by this procedure can be controlled through the sweeping conditions employed. After extended electrografting the defect density reaches a saturation level ( ∼ 10(13) cm(-2)) which is independent of the quality of the graphene expressed through its initial content of defects. However, it is reached within fewer voltammetric cycles for low-quality graphene. Based on these results it is suggested that the grafting occurs (a) directly at defect sites for, in particular, low-quality graphene, (b) directly at the basal plane for, in particular, high-quality graphene, and/or (c) at already grafted molecules to give a mushroom-like film growth for all films. Moreover, it is shown that a tertiary alkyl bromide can be introduced at a given surface density to serve as radical initiator for surface-initiated atom transfer radical polymerization (SI-ATRP). Brushes of poly(methyl methacrylate) are grown from these substrates, and the relationship between polymer thickness and sweeping conditions is studied.

An electrochemical approach is introduced for the versatile carboxylation of multi-layered graphene in 0.1 M Bu4NBF4/MeCN. First, the graphene substrate (i.e., graphene chemically vapor-deposited on Ni) is negatively charged at -1.9 V versus Ag/AgI in a degassed solution to allow for intercalation of Bu4N(+) and, thereby, separation of the individual graphene sheets. In the next step, the strongly activated and nucleophilic graphene is allowed to react with added carbon dioxide in an addition reaction, introducing carboxylate groups stabilized by Bu4N(+) already present. This procedure may be carried out repetitively to further enhance the carboxylation degree under controlled conditions. Encouragingly, the same degree of control is even attainable, if the intercalation and carboxylation is carried out simultaneously in a one-step procedure, consisting of simply electrolyzing in a CO2-saturated solution at the graphene electrode for a given time. The same functionalization degree is obtained for all multi-layered regions, independent of the number of graphene sheets, which is due to the fact that the entire graphene structure is opened in response to the intercalation of Bu4N(+). Hence, this electrochemical method offers a versatile procedure to make all graphene sheets in a multi-layered but expanded structure accessible for functionalization. On a more general level, this approach will provide a versatile way of forming new hybrid materials based on intimate bond coupling to graphene via carboxylate groups.

Highly oriented pyrolytic graphite (HOPG) and graphene grown on Ni (Ni‐Gra) or Cu (Cu‐Gra) by chemical vapour deposition were modified with thick anthraquinone (AQ) films (7−60 nm) by redox grafting of the pertinent diazonium salt. Glassy carbon (GC) electrodes were used for comparison. The AQ‐modified GC electrodes showed excellent blocking properties towards the Fe(CN)63−/4− redox probe, although it was noted that in the case of Ni‐Gra and Cu‐Gra, the blocking ability depended strongly on the underlying substrate. Oxygen reduction studies revealed good electrocatalytic activity of AQ‐modified HOPG, Ni‐Gra, and Cu‐Gra, compared with the bare electrodes.