The tannery industry inevitably generates toxic and catastrophic wastewater, which results in a huge threat to public health and water resources. Therefore, this work aimed to synthesize parthenium hysterophorus-based biochar–Fe3O4 composite for removal of Cr(VI) from tannery wastewater under 34 full factorial experimental designs of the Box–Behnken, which was analyzed using response surface methodology under four independent factors of pH (3, 6, and 9), initial Cr(VI) concentrations (40, 70, and 100 mg/L), contact times (30, 60, and 90 min), and adsorbent doses (20, 60, and 100 mg/100 mL). This composite adsorbent was described by a high BET surface area of 237.4 m2/g, XRD prominent peaks, SEM morphology corroborate and FTIR multifunctionalities of O–H at 3296 cm−1, the vibration of ketone C–OH at 1240 cm−1, and the vibration of C–O–C at 1147 cm−1 and Fe–O stretching at 542 cm−1. The maximum Cr(IV) removal efficiency of 91.8% was recorded at an initial Cr(VI) concentration of 40 mg/L, pH of 3, adsorbent dose of 100 mg/100 mL, and a contact time of 90 min, whereas the minimum Cr(VI) removal of 17.3% was observed at an initial Cr(VI) concentration of 100 mg/L, 20 mg/100 mL of adsorbent dose, pH of 9, and contact time of 30 min. The concentration of Cr(VI) in real wastewater was determined to be 85.13 mg/L and its remediation was found to be 81.8%. Langmuir’s model was the best fit with experimental data at R2 0.99 and qmax 400 mg/g, showing that the adsorption process was homogenous and monolayer. In conclusion, the adsorption results were encouraging, and biochar–Fe3O4 appears to be a potential candidate for Cr removal from wastewater.
Methylene blue (MB) is abundantly found in textile industrial effluent which can cause severe health problems for public and environmental ecology. Therefore, this study aimed to remove MB from textile wastewater using the activated carbon developed from Rumexabyssinicus. The adsorbent was activated using chemical and thermal methods, and then it was characterized by SEM, FTIR, BET, XRD, and pH zero-point charge (pHpzc). The adsorption isotherm and kinetics were also investigated. The experimental design was composed of four factors at three levels (pH (3, 6, and 9), initial MB concentration (100, 150, and 200 mg/L), adsorbent dosage (20, 40, and 60 mg/100 mL), and contact time (20, 40, and 60 min)). The adsorption interaction was evaluated using response surface methodology. The characterization of a Rumexabyssinicus activated carbon was found to have multiple functional groups (FTIR), an amorphous structure (XRD), crack with ups and down morphology (SEM), pHpzc of 5.03 and a high BET-specific surface area of 2522 m2/g. The optimization of MB dye removal was carried out using the Response Surface methodology coupled with the Box Behnken approach. The maximum removal efficiency of 99.9% was recorded at optimum conditions of pH 9, MB concentration of 100 mg/L, the adsorbent dosage of 60 mg/100 mL, and contact time of 60 min. Among the three adsorption isotherm models, the Freundlich isotherm model was the best fit with an experimental value at R2 0.99 showing the adsorption process was heterogeneous and multilayer whereas the kinetics study revealed that pseudo-second-order at R2 0.88. Finally, this adsorption process is quite promising to be used at an industrial level.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.