S U M M A R YA LArge Reservoir Simulator (LARS) was equipped with an electrical resistivity tomography (ERT) array to monitor hydrate formation and dissociation experiments. During two hydrate formation experiments reaching 90 per cent bulk hydrate saturation, frequent measurements of the electrical properties within the sediment sample were performed. Subsequently, several common mixing rules, including two different interpretations of Archie's law, were tested to convert the obtained distribution of the electrical resistivity into the spatial distribution of local hydrate saturation. It turned out that the best results estimating values of local hydrate saturation were obtained using the Archie var-phi approach where the increasing hydrate phase is interpreted as part of the sediment grain framework reducing the sample's porosity. These values of local hydrate saturation were used to determine local permeabilities by applying the Carman-Kozeny relation. The formed hydrates were dissociated via depressurization. The decomposition onset as well as areas featuring hydrates and free gas were inferred from the ERT results. Supplemental consideration of temperature and pressure data granted information on discrete areas of hydrate dissociation.

Gas hydrate production is still in the test phase. It is only now that numerical models are being developed to describe data and production scenarios. Laboratory experiments are carried out to test the rationale of the conceptual models and deliver input data. Major experimental challenges include (I) the simulation of a natural three-phase system of sand−hydrate− liquid with known and high hydrate saturations and (II) the simulation of transport behavior as deduced from field data. The large-scale reservoir simulator (LARS; 210 L sample) at the GFZ has met these challenges and allowed for the first simulation of the gas production test from permafrost hydrates at the Mallik drill site (Canada) via multistage depressurization. At the starting position, hydrate saturation was as high as 90%, formed from dissolved methane only. Whereas gas hydrate dissociation determined the flow patterns in the early pressure stages, the importance of different transport behaviors increased at lower pressure stages and increasing water content. Gas flow patterns as observed in Mallik were recorded. While the conceptual model for the experimental data does agree with the model proposed for Mallik at moderate and low gas production, it is different at high gas production rates.

The LArge Reservoir Simulator (LARS) was developed to investigate various processes during gas hydrate formation and dissociation under simulated in situ conditions of relatively high pressure and low temperature (close to natural conditions). To monitor the spatial hydrate distribution during hydrate formation and the mobility of the free gas phase generated during hydrate dissociation, a cylindrical Electrical Resistivity Tomography (ERT) array was implemented into LARS. The ERT contains 375 electrodes, arranged in 25 circular rings featuring 15 electrodes each. The electrodes were attached to a neoprene jacket surrounding the sediment sample. Circular (2D) dipole-dipole measurements are performed which can be extended with additional 3D cross measurements to provide supplemental data. The data quality is satisfactory, with the mean standard deviation due to permanent background noise and data scattering found to be in the order of 2.12%. The measured data are processed using the inversion software tool Boundless Electrical Resistivity Tomography to solve the inverse problem. Here, we use data recorded in LARS to demonstrate the data quality, sensitivity, and spatial resolution that can be obtained with this ERT array. © 2013 AIP Publishing LLC. [http://dx

The intensive study of hydrate-bearing sandy sediments, a possible source of fossil energy for future generations, leads to an accumulation of information from field studies, laboratory studies, and modeling. This information is used to create conceptual models for hydrate deposit genesis helping to assess the value of laboratory experimental studies on artificially formed hydrate-bearing sediments. We present an experimental example on the simulation of hydrate formation from methane dissolved in water, which is assumed to be the most likely natural process for the genesis of highly concentrated hydrate in sandy sediments. Measurements of the concentration of dissolved methane, temperature, and electrical resistivity tomography are used to describe and characterize the hydrate formation process. It could be shown that the way in which hydrate forms in this laboratory experiment corresponds to the procedure assumed for natural scenarios. The main difference to nature is probably the high crystal growth rate which seems to result in an increased water−hydrate interface and a subsequent "aging" or recrystallization process affecting certain physical properties.

Since huge amounts of CH 4 are bound in natural gas hydrates occurring at active and passive continental margins and in permafrost regions, the production of natural gas from hydrate-bearing sediments has become of more and more interest. Three different methods to destabilize hydrates and release the CH 4 gas are discussed in principle: thermal stimulation, depressurization and chemical stimulation. This study focusses on the thermal stimulation using a counter-current heat-exchange reactor for the in situ combustion of CH 4 . The principle of in situ combustion as a method for thermal stimulation of hydrate bearing sediments has been introduced and discussed earlier [1,2]. In this study we present the first results of several tests performed in a pilot plant scale using a counter-current heat-exchange reactor. The heat of the flameless, catalytic oxidation of CH 4 was used for the decomposition of hydrates in sand within a LArge Reservoir Simulator (LARS). Different catalysts were tested, varying from diverse elements of the platinum group to a universal metal catalyst. The results show differences regarding the conversion rate of CH 4 to CO 2 . The promising results of the latest reactor test, for which LARS was filled with sand and ca. 80% of the pore space was saturated with CH 4 hydrate, are also presented in this study. The data analysis showed that about 15% of the CH 4 gas released from hydrates would have to be used for the successful dissociation of all hydrates in the sediment using thermal stimulation via in situ combustion. OPEN ACCESSEnergies 2013, 6 3003