Synrift stratigraphy and the distribution of breakup-related erosional unconformities vary vastly between passive margins and cannot be explained by classical rifting models. Here we use numerical modeling to predict their spatiotemporal distribution. We show that synrift stratigraphy mimics rift architecture, which is controlled by lithospheric strength. Basinward rift migration during extension produces (1) oceanward younging, syntectonic and posttectonic sequences, (2) rift migration unconformities, RMUs, predating breakup, and (3) a breakup unconformity, BU, that only extends over the outermost margins, since breakup is not linked with a sudden stress drop. With small synrift sedimentation, the RMUs and BU laterally merge to form a margin-wide unconformity. In symmetric, wide conjugate margins, which arise for weak lithospheres such as the South China Sea, a long phase of distributed deformation with little subsidence results in early synrift sediment over most of the margins. RMUs merge into a single event that marks the subsequent focusing of deformation into a narrow breakup area, which experiences short-lived intense thinning and subsidence. In asymmetric conjugate margins, lateral rift migration transports shallowly deposited, early synrift sediments from the narrow to the wide, hyperextended margin, leading to a condensed syntectonic sequence and a single BU in the narrow margin and a series of RMUs in the wide one. For very weak lower crusts, lateral rift migration generates large synrift sag basins in the wide margin, as in Angola and Congo margins. Our models resemble the observed margins tectonic diversity and may be used as templates for interpreting their distal, unexplored areas.

Rifted continental margins may present a predominantly magmatic continent‐ocean transition (COT), or one characterized by large exposures of serpentinized mantle. In this study we use numerical modeling to show the importance of the lower crustal strength in controlling the amount and onset of melting and serpentinization during rifting. We propose that the relative timing between both events controls the nature of the COT. Numerical experiments for half‐extension velocities <=10 mm/yr suggest there is a genetic link between margin tectonic style and COT nature that strongly depends on the lower crustal strength. Our results imply that very slow extension velocities (< 5 mm/yr) and a strong lower crust lead to margins characterized by large oceanward dipping faults, strong syn‐rift subsidence and abrupt crustal tapering beneath the continental shelf. These margins can be either narrow symmetric or asymmetric and present a COT with exhumed serpentinized mantle underlain by some magmatic products. In contrast, a weak lower crust promotes margins with a gentle crustal tapering, small faults dipping both ocean‐ and landward and small syn‐rift subsidence. Their COT is predominantly magmatic at any ultra‐slow extension velocity and perhaps underlain by some serpentinized mantle. These margins can also be either symmetric or asymmetric. Our models predict that magmatic underplating mostly underlies the wide margin at weak asymmetric conjugates, whereas the wide margin is mainly underlain by serpentinized mantle at strong asymmetric margins. Based on this conceptual template, we propose different natures for the COTs in the South Atlantic.

Erosion and deposition redistribute mass as a continental rift evolves, which modifies crustal loads and influences subsequent deformation. Surface processes therefore impact both the architecture and the evolution of passive margins. Here we use coupled numerical models to explore the interactions between the surface, crust, and lithosphere. This interaction is primarily sensitive to the efficiency of the surface processes in transporting mass from source to sink. If transport is efficient, there are two possible outcomes: (1) Faulting within the zone of extension is longer lived and has larger offsets. This implies a reduction of the number of faults and the width of the proximal domain.(2) Efficient transport of sediment leads to significant deposition and hence thermal blanketing. This will induce a switch from brittle to ductile deformation of the upper crust in the distal domains. The feedbacks between these two outcomes depend on the extension history, the underlying lithospheric rheology, and the influence of submarine deposition on sediment transport. High erosion/sedimentation during early faulting leads to abrupt crustal necking, while intermediate syntectonic sedimentation rates over distal deep submarine hotter crust leads to unstructured wide distal domains. In models where rheological conditions favor the formation of asymmetric conjugate margins, only subaerial transport of sediments into the distal domains can increase conjugate symmetry by plastic localization. These models suggest that passive margin architecture can be strongly shaped by the solid Earth structure, sea level, and climatic conditions during breakup. Correspondence to: M. Andrés-Martínez, andresma@uni-bremen.de Citation: Andrés-Martínez, M., Pérez-Gussinyé, M., Armitage, J. J., & Morgan, J. P. (2019). Thermomechanical implications of sediment transport for the architecture and evolution of continental rifts and margins, Tectonics, 38, 641-665.

No abstract

Abstract. We developed a new version of the Alfred Wegener Institute Climate Model (AWI-CM3), which has higher skills in representing the observed climatology and better computational efficiency than its predecessors. Its ocean component FESOM2 (Finite-volumE Sea ice–Ocean Model) has the multi-resolution functionality typical of unstructured-mesh models while still featuring a scalability and efficiency similar to regular-grid models. The atmospheric component OpenIFS (CY43R3) enables the use of the latest developments in the numerical-weather-prediction community in climate sciences. In this paper we describe the coupling of the model components and evaluate the model performance on a variable-resolution (25–125 km) ocean mesh and a 61 km atmosphere grid, which serves as a reference and starting point for other ongoing research activities with AWI-CM3. This includes the exploration of high and variable resolution and the development of a full Earth system model as well as the creation of a new sea ice prediction system. At this early development stage and with the given coarse to medium resolutions, the model already features above-CMIP6-average skills (where CMIP6 denotes Coupled Model Intercomparison Project phase 6) in representing the climatology and competitive model throughput. Finally we identify remaining biases and suggest further improvements to be made to the model.