Superconductors are strategic materials for the fabrication of magnetic shields, and within this class, MgB2 has been proven to be a very promising option. However, a successful approach to produce devices with high shielding ability also requires the availability of suitable simulation tools guiding the optimization process. In this paper, we report on a 3D numerical model based on a vector potential (A)-formulation, exploited to investigate the properties of superconducting (SC) shielding structures with cylindrical symmetry and an aspect ratio of height to diameter approaching one. To this aim, we first explored the viability of this model by solving a benchmark problem and comparing the computation outputs with those obtained with the most used approach based on the H-formulation. This comparison evidenced the full agreement of the computation outcomes as well as the much better performance of the model based on the A-formulation in terms of computation time. Relying on this result, the latter model was exploited to predict the shielding properties of open and single capped MgB2 tubes with and without the superimposition of a ferromagnetic (FM) shield. This investigation highlighted that the addition of the FM shell is very efficient in increasing the shielding factors of the SC screen when the applied magnetic field is tilted with respect to the shield axis. This effect is already significant at low tilt angles and allows compensating the strong decrease in the shielding ability that affects the short tubular SC screens when the external field is applied out of their axis.
The use of superconducting (SC) materials is crucial for shielding quasi-static magnetic fields. However, the frequent requisite of space-saving solutions with high shielding performance requires the development of a 3D modelling procedure capable of predicting the screening properties for different orientations of the applied field. In this paper, we exploited a 3D numerical model based on a vector potential formulation to investigate the shielding ability of SC screens with cylindrical symmetry and a height/diameter aspect ratio close to unity, without and with the superimposition of a ferromagnetic (FM) circular shell. The chosen materials were MgB2 and soft iron. First, the calculation outcomes were compared with the experimental data obtained on different shielding arrangements, achieving a notable agreement in both axial-field (AF) and transverse-field (TF) orientations. Then, we used the thus validated modelling approach to investigate how the magnetic mitigation properties of a cup-shaped SC bulk can be improved by the superimposition of a coaxial FM cup. Calculations highlighted that the FM addition is very efficient in enhancing the shielding factors (SFs) in the TF orientation. Assuming a working temperature of 30 K and using a layout with the FM cup protruding over the SC one, shielding factors up to 8 times greater than those of the single SC cup were attained at low applied fields, reaching values equal or higher than 102 in the inner half of the shield. In the AF orientation, the same FM cup addition costs a modest worsening at low fields, but at the same time, it widens the applied field range, where SF ≥ 104 occurs near the close extremity of the shield, up over 1 T.
Fe40Ni40B20 metallic glass is a key material among the many amorphous systems investigated thus far, owing to its high strength and appealing soft magnetic properties that make it suitable for use as transformer cores. In this study, Fe40Ni40B20 microfibers are fabricated down to 5 µm diameter. Three different melt–spinning wheel velocities: ≈51 m s−1, ≈59 m s−1, and ≈63 m s−1 (MG1, MG2, MG3) are used. Their fully amorphous structure is confirmed using X–ray diffraction, and differential scanning calorimetry (DSC) traces reveal a larger relaxation profile for the higher–quenched microfiber. Vibrating sample magnetometer measurements showed a higher saturation magnetization of 136 emug−1 for annealed metallic glass microfibers with a wheel velocity of 59.66 ms−1. Cylindrical magnetic field shields are obtained by aligning and wrapping the fibers around a cast. The observed anisotropic static field shielding behavior is in accordance with the microfibers' anisotropic nature. Composite samples are also produced by embedding the microfibers in an epoxy matrix to investigate their electromagnetic properties at GHz frequencies. Inclusion of the microfibers increase the composite's attenuation constant by 20 to 25 times, making it an ideal candidate for applications in the communications frequency range.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.