The evolution of microstructure and mechanical properties in AISI 8630 low-alloy steel subjected to inertia friction welding (IFW) have been investigated. The effects of three critical process parameters, viz. rotational speed, friction and forge forces, during welding of tubular specimens were explored. The mechanical properties of these weld joints, including tensile and Charpy V-notch impact were studied for determining the optimum welding parameters. The weld joints exhibited higher yield strength, lower hardening capacity and ultimate tensile strength compared to base metal (BM). The maximum strength and ductility combination was achieved for the welds produced under a nominal weld speed of ~ 2900–3100 rpm, the highest friction force of ~ 680–720 kN, and the lowest axial forging load of ~ 560–600 kN. The measured hardness distribution depicted higher values for the weld zone (WZ) compared to the thermo-mechanically affected zone (TMAZ), heat-affected zone (HAZ) and BM, irrespective of the applied welding parameters. The substantial increase in the hardness of the WZ is due to the formation of microstructures that were dominated by martensite. The observed microstructural features, i.e. the fractions of martensite, bainite and ferrite, show that the temperature in the WZ and TMAZ was above Ac3, whereas that of the HAZ was below Ac1 during the IFW. The fracture surface of the tensile and impact-tested specimens exhibited the presence of dimples nucleating from the voids, thus indicating a ductile failure. EBSD maps of the WZ revealed the formation of subgrains inside the prior austenite grains, indicating the occurrence of continuous dynamic recrystallisation during the weld. Analysis of crystallographic texture indicated that the austenite microstructure (i.e. FCC) in both the WZ and TMAZ undergoes simple shear deformation during IFW.
Continuous drive friction welding (CDW) is a state-of-the-art solid-state welding technology for joining metallic components used in aerospace, oil and gas and power generation industries. This study summarises the results of mechanical and microstructural investigations on a modified AISI-8630 steel subjected to CDW. The effects of welding process parameters, including rotational speed, friction and forge forces, during CDW were explored to determine an optimum welding condition. The mechanical properties of the weld, and microstructural characteristics across different regions of the weld were measured and examined. The microstructure characterisation results suggest that the weld zone (WZ) experiences temperatures above Ac3 and the thermo-mechanically affected zone (TMAZ) experiences temperatures between Ac1 and Ac3 of the material. Investigations with electron backscatter diffraction (EBSD) demonstrated the occurrence of strain-induced dynamic recrystallisation in the weld. The weld demonstrated higher yield and ultimate tensile strengths at the expense of ductility and hardening capacity compared to the base metal (BM). The strain hardening profiles of the welds exhibited a dual-slopes characteristic, an indication of different levels of plastic deformation experienced by the constituent phases (i.e., martensite, bainite and ferrite) present in the microstructure. The maximum strength-to-ductility combination and static toughness values were obtained for the weld produced under the highest rotational speed, maximum friction force and an intermediate forge force of 1200-1400 rpm, 37.5-42.5 kN and 60-65 kN, respectively.
Mechanical properties of a REX734 austenitic stainless steel were examined through compression testing over a wide range of temperatures (1173 K to 1373 K (900 °C to 1100 °C)) and strain rates (0.1 to 40 s−1) that cover deformation conditions encountered in different metalworking processes. The evolution of microstructure was studied using electron microscopy combined with electron backscatter diffraction and energy-dispersive spectroscopy. Partially recrystallized microstructures were obtained after compression testing at 1173 K (900 °C), while after deformation at 1273 K and 1373 K (1000 °C and 1100 °C), the material was fully recrystallized almost in all examined cases. The role of dynamic and metadynamic restoration processes in the formation of final microstructure was investigated. Σ3 twin boundaries lost their twin character and transformed into general high-angle grain boundaries as a result of deformation, while during recrystallization new Σ3 twin boundaries formed. The evolution of precipitates during compression testing and their role in the recrystallization process was also discussed.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.